- Out-of-Stock
Starter kit with NanoPi NEO 512 MB
ID: 572009
Starter kit with NanoPi NEO minicomputer. The set includes a NanoPi NEO 512MB minicomputer, an aluminum housing, a NanoHat OLED display, a MicroUSB cable, a heat sink, an 16GB memory card and the necessary mounting hardware. FriendlyELEC NEO Metal Complete Kit
Description
Starter kit with NanoPi NEO minicomputer. The set includes a NanoPi NEO 512 MB minicomputer, an aluminum housing, a NanoHat OLED display, a microUSB cable, a heat sink, an 16 GB memory card and the necessary mounting hardware.
properties
NanoPi NEO:
- SoC Allwinner H3 system (quad-core, ARM Cortex-A7)
- DDR3 RAM memory with 512 MB capacity
- 8 GB eMMC memory
- MicroSD card slot
- Ethernet 10 / 100M interface derived from the GPIO port
- Audio input / output lead to the GPIO port
- Micro USB OTG port also used as power input
- 3 USB ports are output to the GPIO port
- GPIO ports: 2 24-pin and 20-pin ports, including UART, SPI, I2C, USB, I2S, Ethernet, GPIO interfaces, etc.
- 2 LEDs
- Power supply: DC 5V / 2A
NanoHat OLED
- LCD size: 0.96 inches
- Resolution: 128 x 64 pixels
- High contrast, low energy consumption
- 3 x button
- Dimensions of the printed circuit board: 40 x 40 mm
Assembly instructions
Included
- NanoPi NEO 512 MB
- NanoHat OLED
- Aluminum housing
- MicroUSB cable
- Radiator with thermoconductive tape and screws
- MicroSD memory card (16 GB)
572009
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
1/4 Inch 5 Megapixels Sensor Spy Camera Module with Flex Cable for Raspberry Pi. ArduCAM B0066
zł187.42
24h
Available quantity: 15
Available
NanoPi NEO Core Allwinner H3 Quad-Core 1,2Ghz + 256MB RAM
Regular pricezł168.69zł129.09
24h
Available quantity: 6
Available
Minicomputer with Allwinner H3 quad-core chip (ARM Cortex-A7). It is equipped with 512 MB RAM memory, an Ethernet port and 3 USB 2.0 interfaces. NanoPi NEO-LTS 512MB
zł159.35
24h
Available quantity: 2
Available
Other products in the same category (16)
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Multicolor Silk Jungle
Retired
No product available!
No product available!
No product available!
RoboClaw 2x60A Motor Controller (V6) is a two-channel DC motor driver, operating voltage: 6-34V, maximum continuous current: 60A, easy implementation of feedback loops with PID controller, safety systems. Pololu 3289
Retired
No product available!
Assembled regulated symmetrical voltage supply. AVT1882 C
Retired
No product available!
No product available!
Pre-installed Ubuntu 14.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung.
JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode
Retired
No product available!
Waveshare AlphaBot, a kit for building an Arduino-based robot with Bluetooth and the Arduino extension
Retired
No product available!
No product available!
No product available!
No product available!
No product available!
No product available!
Test probe tip with 500X attenuation factor. Dedicated to Micsig probes from the SigOFIT series operating in the 100 MHz and 200 MHz frequency bands. Micsig OP500-2
Product available on request. Please send your inquiry to the following address: sales@kamami.com
Retired
No product available!
No product available!
Starter kit with NanoPi NEO minicomputer. The set includes a NanoPi NEO 512MB minicomputer, an aluminum housing, a NanoHat OLED display, a MicroUSB cable, a heat sink, an 16GB memory card and the necessary mounting hardware. FriendlyELEC NEO Metal Complete Kit