.png)
- Out-of-Stock
AVT1996 A + - night lighting controller with motion detector. PCB and programmed layout
ID: 572355
Printed circuit board and programmed system for Bedlight - night lighting controller with motion detector. AVT1996 A +
Description
A time switch with a motion sensor that can flexibly configure work parameters. It acts as an automatically switched on night lighting and is designed to work with LED strips. Detection of motion in a room with poor lighting conditions starts the timing system, smoothly brightening the LED light source connected to the output. After the time set by the potentiometer, its smooth, slow extinguishment follows. After assembly, the system is ready for operation immediately, it only requires carrying out the configuration appropriate for the needs.
Project AVT 1996 EP 08/18
572355
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
A universal set of structural elements (plastic beams, plates, metal brackets and fasteners, and a set of screws and nuts). It also includes the necessary tools. Totem TKM-MK2
Retired
No product available!
A universal set of structural elements (plastic beams, plates, metal brackets and fasteners, and a set of screws and nuts). It also includes the necessary tools. Totem TKM-MK3
Retired
No product available!
A set for building an electronic laboratory based on a TotemDuino board. It is a great platform for experimenting, learning electronics and programming Arduino. Totem TKM-MCL1
Retired
No product available!
Side panel with I/O elements for Totem Mini Lab and Totem Micro Lab sets. There are buttons, potentiometers, LED diodes and a relay on the board. Totem TE-SP01-B
Retired
No product available!
Side panel with sensors for Totem Mini Lab and Totem Micro Lab sets. The board has a microphone, OLED display, DH11 humidity sensor, NTC thermistor, buzzer and a DC motor control module. Totem TE-SP02-B
Retired
No product available!
Side panel with audio elements for Totem Mini Lab and Totem Micro Lab sets. The board has an audio amplifier with a loudspeaker, a VU indicator, a function generator and a pi filter circuit. Totem TE-SP03-B
Retired
No product available!
A stand for mounting the side panel for the Totem Mini Lab set. Increases the stability of the structure. Totem M-MLE1
Retired
No product available!
A set for building a fighting robot controlled by a mobile application for a smartphone or tablet. Totem TRK-MT1G
Retired
No product available!
A set for the construction of two fighting robots (green and yellow) controlled by a mobile application for a smartphone or tablet. Totem TRK-MT2
Retired
No product available!
A kit for building a four-wheeled platform controlled by a mobile application. TMK-4WDU totem
Retired
No product available!
A set for building a mobile robot with a gripper controlled by a mobile application. TMK-DMNNG totem
Retired
No product available!
Kit for building a dog robot controlled by a wire with a switch. Totem TKR-DG
Retired
No product available!
Kit for building a giraffe robot controlled by a wire with a switch. Totem TKR-GRF
Retired
No product available!
Kit for building a dinosaur robot controlled by a wire with a switch. Totem TKR-TRX
Retired
No product available!
A set for building a walking robot controlled by a mobile application. Totem TKR-LSP
Retired
No product available!
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and output on pads. It enables powering devices with 9 V or 12 V and testing chargers. PDC005
Retired
No product available!
Printed circuit board and programmed system for Bedlight - night lighting controller with motion detector. AVT1996 A +