- Out-of-Stock
Filament ROSA3D PLA Plus ProSpeed 1.75mm Black 3kg
ID: 587751
5907753131058
ROSA3D filament made of high-quality PLA granules. 3 kg of 1.75 mm filament is wound on the spool. ROSA3D PLA Plus ProSpeed Black
Description
1.75 mm PLA filament for 3D printing by ROSA3D. 3 kg of filament is wound on the spool. The recommended printing temperature is in the range of 190°C to 230°C, and the temperature of the bed during printing in the range of 50°C to 70°C, however, when using adhesives, heating the bed is not necessary.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament.
The PLA Plus ProSpeed series is dedicated to the industry. It is perfect for continuous printing, taking many hours, where there is a need to print at high speed.
The PLA Plus ProSpeed filament offers better mechanical and temperature resistance than PLA Starter. The impact strength measured by the Izod method is almost 1.5 times higher than that of standard ABS, and after crystallization - more than twice as high. The filament is made of biodegradable biopolymer and is an alternative to styrene-based materials. PLA Plus ProSpeed provides excellent print quality, good adhesion to the print bed, less warping and no irritating smell. It was made of ingredients approved for contact with food.
Features
- Color: Black
- Diameter: 1.75 mm
- Diameter tolerance: +/- 0.05mm
- Oval tolerance: +/- 0.02mm
- Printing temperature: 190°C to 230°C
- Bed temperature: 50°C to 70°C (when using washers or other means to increase the adhesion heating of the table is not required)
- Print speed: 60 to 80 mm/s
- Density 1.22 g/cm3
- Odor: odorless
- Tensile strength (to break) XY axis - 40 MPa; YX axis - 32 MPa; ZX axis - 24 MPa
- Modulus of elasticity in tension XY axis - 2865 MPa; YX axis - 2447 MPa; ZX axis - 2477 MPa
- Heat deformation temperature 75-85 ° C (after annealing)
- Impact strength according to the Izod method with the notch XY axis - 160 J / m; YX axis - 21 J / m; ZX axis - 109 J / m
- Net weight: 3 kg
587751
Data sheet
- Rodzaj filamentu
- PLA
- Ilość filamentu
- 3 kg
- Diameter
- 1,75 mm
- Colour
- Black
You might also like
3D printer with dual color print and heated table. The printer is fully assembled and ready to use. Flashforge Creator PRO
Regular pricezł4,365.91zł3,199.00
24h
Available quantity: 1
Available
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
zł9.40
Delivery date unknown
No product available!
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
zł52.90
24h
Available quantity: 74
Available
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
zł54.46
24h
Available quantity: 265
Available
3D printer with two extruder and a heated table. It is fully assembled and ready to use. Flashforge Creator Pro 2
Regular pricezł5,292.28zł3,999.00
24h
Available quantity: 1
Available
Other products in the same category (16)
Waveshare camera module with OV7670 chip, 0.3 megapixels, resolution up to 640x480 pixels. It enables downloading of images in various formats via the Serial Camera Control Bus (SCCB) interface at 30 fps. Waveshare 9828
Retired
No product available!
Raspberry Pi 3 & MathWorks Learn to Program Pack is a set consisting of a Raspberry Pi 3 computer with necessary hardware and MATLAB & Simulink Student Suite software. The set is designed for modeling and implementing solutions based on Raspberry Pi 3 in MATLAB and SIMULINK environments
Retired
No product available!
IBM Watson IoT Platform is a set containing a computer Raspberry Pi 3 model B and Shield Raspberry Pi Sense HAT together with a course on modeling, simulation and analysis of projects related to Raspberry Pi 3 in IoT (Internet of Things) systems. PI3 IBM IOT LEARNKIT
Retired
No product available!
Battery: Li-Ion; 3.7V; 400mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13851
Retired
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
Retired
No product available!
3DR Radio is a set that allows bidirectional transmission of telemetry data, eg between the RC model (with the APM controller) and a PC. Light and small device in a set with antennas and connecting cables. Radio modules have a power of 100mW (+ 20dBm) and transmit a signal over a distance of 1km.
Retired
No product available!
A small USB splitter allowing to connect up to 4 USB devices, powered from the USB port
Retired
No product available!
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. Each Teensy 3.2 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! PJRC TEENSY32
Retired
No product available!
No product available!
This is the Teensy Audio board add-on for the Teensy 3.x line development boards. This audio board provides you with an easy-to-use tool to add high quality 16 bit, 44.1 kHz sample rate audio to your Teensy project. PJRC TEENSY3-AUDIO
Retired
No product available!
No product available!
No product available!
No product available!
AVT kit for self-assembly of the USB-1-Wire converter. AVT1787 B
Retired
No product available!
No product available!
PCB for MKP - control and measurement module with USB interface. AVT5425 A
Retired
No product available!
ROSA3D filament made of high-quality PLA granules. 3 kg of 1.75 mm filament is wound on the spool. ROSA3D PLA Plus ProSpeed Black