- Out-of-Stock
1.75 mm PLA filament for 3D printing by ROSA3D. 0.8 kg of filament is wound on the spool. The recommended printing temperature is in the range from 185°C to 225°C, and the bed temperature during printing in the range of 40°C - 60°C, however, when using adhesives, heating the bed is not necessary.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. Filament PLA Starter from Rosa3D was designed for beginner users of 3D printers. The simplicity of PLA Starter printing will allow you to enjoy aesthetic prints, and over time will convince you to print more and more complex and demanding projects.
PLA is the basic material used in 3D printing. PLA Starter is characterized by low shrinkage and no unpleasant odor. The prints are characterized by excellent layer adhesion and very good detail reproduction. The filament is made of a biodegradable biopolymer. It was made of ingredients approved for contact with food.
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
Module with Xilinx Artix-7 100T system and 32MB FLASH memory. TE0725LP-01-100-2C
No product available!
Module with Xilinx Artix-7 100T system and 32MB FLASH memory. TE0725LP-01-100-2D
No product available!
Module with Xilinx Artix-7 100T system and 32MB FLASH memory. TE0725LP-01-100-2L
No product available!
Base plate designed to work with TE0808 and TE0803 modules. It allows you to connect the module to external connectors and interfaces. TEBT0808-01
No product available!
Base plate designed to work with TE0745 modules. TEB0745-02
No product available!
Base plate for Trenz Electronics 4x5 cm modules, e.g. TE0741, TE0712. The board allows connecting to the module interfaces: USB, Ethernet, JTAG. TE0705-04
No product available!
Base plate for Trenz Electronic 4 x 5 cm modules. It allows you to connect an FPGA system through board-to-board connections to external peripherals to test and develop software. TE0701-06
No product available!
UltraITX + base board designed to work with TE0808 UltraSOM + MPSoC modules. It allows you to connect the module to external connectors and interfaces. TEBF0808-04
No product available!
TEBA0841 is a base plate for Trenz Electronic 4 x 5 modules, e.g. TE0741 series. The FPGA input / output ports can be connected directly to the periphery via two 50 pin goldpin connectors. TEBA0841-01
No product available!
TE0706 is a base plate for Trenz Electronic 4x5cm Muduors. It allows you to connect USB, JTAG and Ethernet interfaces. TE0706-02
No product available!
Base plate for Trenz Electronics modules 4 x 5 cm, eg for TE0741. The board allows connecting to the module interfaces: USB, Ethernet, JTAG, UART. TE0703-05
No product available!
USB TO UART solution with USB Type A connector, Waveshare
No product available!
No product available!
The second version of the clock synchronization signal receiver, transmitted with AM modulation (DCF77). The built-in MAS6180 system allows you to receive timing frames from a time pattern using a carrier frequency of 77.5 kHz. Thanks to this module, it is possible to create a clock with automatic date and time synchronization. The module has a ferrite antenna. modDCF77 v2
No product available!
Pyboard is a compact development board that allows you to use the MicroPhyton software. Min. 3-axis accelerometer (MMA7670), diodes, monostable buttons and microSD memory card slot. Adafruit 3497
No product available!
LCD touch screen with 160x128 pixel resolution, LCD160CR (I2C or UART and SPI) display controller. Adafruit 3498
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Red Jasper Satin