- Out-of-Stock
New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
USB2 Module
ID: 60089
USB2 Accessory Board
USB2 Accessory Board
The Digilent USB2 Module Board (the USB2) is used to connect any Digilent system board to a USB 2.0 connection. The USB2 is based on the Cypress CY7C68013 USB controller and can be used to configure system boards or exchange data with a PC. Digilent firmware in the Cypress USB controller works with Digilent's PC-based Adept Software to coordinate JTAG programming and user data transfers. The user data port uses the 14 signal "Enhanced Parallel Port" (EPP) protocol.
The firmware in the Cypress USB controller can be modified using the Cypress EZ-USB development kit availabale from Cypress. (Digilent does not offer user support for modifying this firmware.)
The USB2 is compatable with all newer Digilent system boards including the Spartan-3, Pegasus, D2SB, and D2FT boards. It can also be used with the older D2 and D2E boards for user data transfers, but not for programming.
Please visit Adept Software Page to download the Adept Suite.
Code: 210-054
The Digilent USB2 Module Board (the USB2) is used to connect any Digilent system board to a USB 2.0 connection. The USB2 is based on the Cypress CY7C68013 USB controller and can be used to configure system boards or exchange data with a PC. Digilent firmware in the Cypress USB controller works with Digilent's PC-based Adept Software to coordinate JTAG programming and user data transfers. The user data port uses the 14 signal "Enhanced Parallel Port" (EPP) protocol.
The firmware in the Cypress USB controller can be modified using the Cypress EZ-USB development kit availabale from Cypress. (Digilent does not offer user support for modifying this firmware.)
The USB2 is compatable with all newer Digilent system boards including the Spartan-3, Pegasus, D2SB, and D2FT boards. It can also be used with the older D2 and D2E boards for user data transfers, but not for programming.
Please visit Adept Software Page to download the Adept Suite.
Key Features:
- USB 2.0 connector
- Status Indicator LED
- Cypress CY7C68013 USB Controller
- Small Form Factor (3.00" x 2.20")
- Used with the free Digilent Adept Suite Software
Code: 210-054
60089
Other products in the same category (16)
No product available!
Li-Po battery 3.7V / 320mAh, PCM safety, connector + JST-BEC 2,54 socket, 2 pins, cable length 150mm
Retired
No product available!
Delivery date unknown
No product available!
Delivery date unknown
No product available!
USB WiFi adapter for Odroid minicomputers. It has a built-in 2.4GHz and 5.8GHz Dual band antenna. Compatible with Android and Linux systems. Odroid Wifi Module 5A
Retired
No product available!
No product available!
Miniature (22x13.5x6mm) WiFi module b / g / n with TCP and UDP protocols operating in standalone and access point modes. 2.0mm goldpin connector. The module is equipped with a UART interface, it is also possible to control GPIO lines (also as PWM). Powered by 3.3V. I-PEX connector
Delivery date unknown
No product available!
No product available!
John Sabin, Sylvio Canuto
Delivery date unknown
No product available!
No product available!
Premium Jumper Wire 50-Piece Rainbow Assortment M-M 12"
Retired
No product available!
No product available!
No product available!
Power cord with a length of 50 cm with a male XT60 plug and a DC Jack 5.5 x 2.5 mm plug. It allows you to connect a battery with an XT60 socket to a device with a DC socket
Retired
No product available!
Miniature, remote controlled robot (Mini R / C Battle Robot) with RC 2.4GHz remote control, charger and traffic lights. Black colour.
Retired
No product available!
Pin strip straight in black, double-breasted, female, 2x14, pitch 2.54mm, THT, RoHS. PBD28S
Retired
No product available!
USB2 Accessory Board