![Segger J-Link 9-pin Cortex-M Adapter (8.06.02) Segger J-Link 9-pin Cortex-M Adapter (8.06.02)](https://kamami.pl/15555-large_default/j-link-9-pin-cortex-m-adapter-rohs-segger.jpg)
![Segger J-Link 9-pin Cortex-M Adapter (8.06.02) Segger J-Link 9-pin Cortex-M Adapter (8.06.02)](https://kamami.pl/15555-large_default/j-link-9-pin-cortex-m-adapter-rohs-segger.jpg)
zł138.45 tax excl.
J-Link 9-pin Cortex-M Adapter, RoHS, Segger
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
J-Link 9-pin Cortex-M Adapter, RoHS, Segger
The J-Link 9-pin Cortex-M Adapter allows JTAG, SWD and SWO connections between J-Link and Cortex-M based target hardware systems. It adapts from the 20-pin 0.1 JTAG connector to a 9-pin 0.05 Samtec FTSH connector as defined by ARM.
The J-Link 9-pin Cortex-M Adapter may also be used to connect J-Link to a non Cortex-M target as far as the target connector uses the same pinout as shown below.
By default, TRST is not connected, but the Cortex-M Adapter comes with a solder bridge (NR1) which allows TRST to be connected to pin 9 of the Cortex-M adapter.
Code: J-Link 9-pin Cortex-M Adapter (8.06.02)
JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)
A power adapter that provides a stabilized supply voltage to the target board (can be adjusted from 3.6V to 0.8V). Segger Target Supply Adapter (8.06.18)
No product available!
10-pin Needle Adapter to connect Flasher 5, Flasher ST7 or Flasher STM8 to a PCB, Segger
No product available!
An advanced device that allows real-time tracking and analysis of code executed on a RISC-V core chip. Segger J-Trace PRO for Cortex (8.20.00)
No product available!
An adapter that converts a standard 20-pin 2.54 mm connector to a 10-pin 2.54 mm connector. It enables the connection of Segger programmers with Silicon Labs devices and development boards with a C2 interface. Segger SiLabs C2 Adapter (8.06.17)
No product available!
The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)
No product available!
An adapter to connect the JTAG to a target hardware system that has an automotive connector. It has a 20 pin 2.54mm JTAG connector and a 19 pin 1.27mm Samtec FTSH connector. Segger Infineon AUTO-20 Adapter (8.06.33)
No product available!
SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)
No product available!
No product available!
Flash Programmer for ARM and Cortex cores, Segger
No product available!
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission. (j-trace-pro)
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
No product available!
J-Link 19-pin Cortex-M Adapter, RoHS, Segger
JTAG/SWD debug probe with USB interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-Link is used around the world in tens of thousand places for development and production (flash programming) purposes. J-link PLUS Compact (8.19.28)
J-Link 9-pin Cortex-M Adapter, RoHS, Segger