Voltage Regulator module 9V Step-Down 2.6A D36V28F9
ID: 586591
zł90.95
Tax included
zł73.94 tax excl.
Step-Down converter D36V28F9 with an output voltage of 9 V, an input voltage from 9.8 to 50 V and a maximum output current of 3.4 A. Pololu 3785
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Step-Down converter module D36V28F9 with an output voltage of 9 V and an input voltage from 9.8 to 50 V. The maximum current load of the module is from 2.3 to 3.4 A and depends on the input voltage. The inverter achieves a standard efficiency of over 80-90%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinout
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
Features
- Input voltage: 9.8 to 50V
- Output voltage: 9V
- Type. maximum current: from 2.3 to 3.4 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-90%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 3 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Two M2 mounting holes
- Dimensions: 17.8 x 20.3 x 8.8 mm
Parameters
Kit contains
- D36V28F9 converter module
- Straight 6-pin goldpin connector
- 5-pin angled goldpin connector
586591
Data sheet
- Output voltage
- 9 V
- Output current
- 2,6 V
- Converter type
- Step-down
- Supply voltage min
- 9,8 V
- Supply voltages max
- 50 V
You might also like
The Step-Up Buck Voltage Regulator module with adjustable output voltage in range of 4-25V with a input voltage range of 1.5-16V and a maximum output current of 2A. Pololu 799
zł70.86
24h
Available quantity: 3
Available
Step-Up converter U3V70A with an output voltage from 4.5 to 20 V, an input voltage from 2.9 to VOUT and a maximum output current of 10 A. Pololu 2890
zł111.47
Delivery date unknown
No product available!
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł39.90
Delivery date unknown
No product available!
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.90
24h
Available quantity: 1346
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.34
24h
Available quantity: 58
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.72
24h
Available quantity: 212
Available
Step-Down converter D36V50F9 with an output voltage of 9 V, an input voltage from 9.9 to 50 V and a maximum output current of 7 A. Pololu 4094
zł120.88
24h
Available quantity: 1
Available
Other products in the same category (16)
Step-Down converter with adjustable output voltage from 1.25 to 36 V, input voltage from 4 to 38 V and maximum current up to 5 A
zł7.68
24h
Available quantity: 72
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage from 4 V to 36 V and efficiently reduces it to 3.3 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.6 A and features reverse voltage protection.
zł53.14
24h
Available quantity: 3
Available
Step-Down DC-DC converter module based on the D36V6F5 chip. Input voltage 5.2..50V, output voltage 5V (max. 600mA). Pololu 3792
zł29.54
24h
Available quantity: 2
Available
Step Down DC-DC converter module based on LM2596 circuit, input voltage 3-40V, regulated output voltage 1.5--35V
zł4.34
24h
Available quantity: 170
Available
Step-Down converter D36V50F6 with an output voltage of 6 V, an input voltage from 6.5 to 50 V and a maximum output current of 8 A. Pololu 4092
zł120.88
24h
Available quantity: 1
Available
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
zł120.88
24h
Available quantity: 2
Available
A power supply based on a DC-DC converter with a current capacity of up to 5 A. The input voltage can range from 6 V to 36 V, while the output voltage is adjustable from 0.6 V to 36 V. XYS3580
zł127.00
24h
Available quantity: 4
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 9 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł81.11
24h
Available quantity: 1
Available
Step-Down converter D36V50F12 with an output voltage of 12 V, an input voltage from 13.3 to 50 V and a maximum output current of 6.5 A. Pololu 4095
zł127.06
24h
Available quantity: 4
Available
A power supply based on a DC-DC converter with a current capacity of up to 5.1 A. The input voltage can range from 5 V to 30 V, while the output voltage is adjustable from 0 V to 36 V. XY3605
zł288.99
24h
Available quantity: 2
Available
DC-DC Step-Down converter module with 5V output voltage and 1A output current. The module can be a replacement for the popular LM7805 regulator.
zł6.65
6 weeks
No product available!
The Step-Down D24V3AHV Buck Voltage Regulator module with adjustable output voltage in the range of 4-25V with a wide input voltage range of 4.5-42V and a maximum output current of 300 mA. Pololu 2102
zł32.69
24h
Available quantity: 1
Available
The compact (0.4″ × 0.5″) D24V5F1 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 1.8 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 75% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
zł28.40
24h
Available quantity: 1
Available
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40V and efficiently reduces it to 5V with an available output current of around 15A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for powering large loads. Pololu 2881
zł459.00
24h
Available quantity: 1
Available
A power supply based on a DC-DC converter with a current capacity of up to 6.1 A. The input voltage can range from 6 V to 30 V, while the output voltage is adjustable from 0 V to 36 V. XYL3606S
zł119.00
24h
Available quantity: 5
Available
No product available!
Step-Down converter D36V28F9 with an output voltage of 9 V, an input voltage from 9.8 to 50 V and a maximum output current of 3.4 A. Pololu 3785