Voltage Regulator module 3.3V Step-Down 6.5A D36V50F3
ID: 586581
zł120.88
Tax included
zł98.28 tax excl.
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Step-Down converter module D36V50F3 with an output voltage of 3.3 V and an input voltage from 4.5 to 50 V. The maximum current load of the module is from 4.5 to 9.5 A and depends on the input voltage. The inverter achieves standard efficiency above 80-95%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinot
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
- VRP - provides access to the input voltage before protection against voltage reverse polarity. Can be used as an output to power other devices or the input voltage can be connected to VRP instead of VIN to bypass protection.
Features
- Input voltage: 4.5 to 50V
- Output voltage: 3.3V
- Type. maximum current: from 4.5 to 9.5 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-95%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 4 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Three mounting holes M2
- Dimensions: 25.4 x 25.4 x 9.5 mm
Parameters
Kit contains
- D36V50F3 converter module
- 12-pin straight goldpin connector
586581
Data sheet
- Output voltage
- 3,3 V
- Output current
- 6.5A
- Converter type
- Step-down
- Supply voltage min
- 4,5 V
- Supply voltages max
- 50 V
You might also like
Pololu 12V Step-Up Voltage Regulator U3V50F12
zł131.76
24h
Available quantity: 2
Available
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł39.90
Delivery date unknown
No product available!
Step-Down converter D36V50F6 with an output voltage of 6 V, an input voltage from 6.5 to 50 V and a maximum output current of 8 A. Pololu 4092
zł120.88
24h
Available quantity: 1
Available
Step-Down converter D36V50F12 with an output voltage of 12 V, an input voltage from 13.3 to 50 V and a maximum output current of 6.5 A. Pololu 4095
zł127.06
24h
Available quantity: 4
Available
Other products in the same category (16)
The compact (0.4″ × 0.5″) D24V5F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 500 mA. Pololu 2843
zł26.03
6 weeks
No product available!
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 3.3 V with an available output current of around 15 A. Pololu 2880
zł496.08
6 weeks
No product available!
Step-Down DC-DC converter module based on the D24V150F12 chip. Input voltage 14.5 ... 40V, output voltage 12V (max 15A). Pololu 2885
zł500.72
24h
Available quantity: 1
Available
Available
The compact (0.4″ × 0.5″) D24V5F6 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 6 V while allowing for a maximum output current of 500 mA. Pololu 2844
zł28.40
6 weeks
No product available!
Step-Down converter with an output voltage of 5 V, an input voltage of 7 to 26 V and a maximum current of 3 A
zł7.20
24h
Available quantity: 132
Available
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 6 V with an available output current of around 15 A. Pololu 2882
zł497.17
24h
Available quantity: 1
Available
The compact (0.4″ × 0.5″) D24V5F9 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 9 V while allowing for a maximum output current of 500 mA. Pololu 2845
zł28.82
24h
Available quantity: 1
Available
Step-Down converter D36V50F5 with an output voltage of 5 V, an input voltage from 5.5 to 50 V and a maximum output current of 8 A. Pololu 4091
zł120.96
24h
Available quantity: 2
Available
An isolated DC-DC converter that can be powered from 36 to 72 V DC and supplies 5 V DC and up to 20 A. The device is supplied in an IP65 enclosure. SparkFun COM-18733
zł179.90
6 weeks
No product available!
The compact (0.4″ × 0.5″) D24V5F12 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 12 V while allowing for a maximum output current of 500 mA.
zł28.62
24h
Available quantity: 4
Available
The compact (0.4″ × 0.5″) D24V5F1 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 1.8 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 75% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
zł28.40
24h
Available quantity: 1
Available
The very small step-down 6 V, 2.5 A synchronous inverter can be supplied with voltage up to 36 V, dimensions: 17.8 mm x 17.8 mm. Pololu 2859
zł61.12
6 weeks
No product available!
No product available!
Modular power supply with a power of 3 W, input voltage from 100 to 240 V and output voltage of 3.3 V. Designed for mounting on a PCB. Hi-Link HLK-PM03
zł16.72
24h
Available quantity: 10
Available
The energy harvesting module based on the LTC3588 chip, which is a complete energy harvesting solution for sources such as piezoelectric, solar or magnetic transducers. SparkFun BOB-09946
zł199.65
24h
Available quantity: 1
Available
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090