New products
New products
zł67.99
24h
Available
zł69.00
24h
Available
zł67.99
24h
Available
Available
zł79.00
24h
Available
zł67.99
24h
Available
zł69.00
24h
Available
zł67.99
24h
Available
Available
zł79.00
24h
Available
Voltage Regulator module 9V Step-Down 2.6A D36V28F9
ID: 586591
5906623413140
zł90.95
Tax included
zł73.94 tax excl.
Step-Down converter D36V28F9 with an output voltage of 9 V, an input voltage from 9.8 to 50 V and a maximum output current of 3.4 A. Pololu 3785
Description
Step-Down converter module D36V28F9 with an output voltage of 9 V and an input voltage from 9.8 to 50 V. The maximum current load of the module is from 2.3 to 3.4 A and depends on the input voltage. The inverter achieves a standard efficiency of over 80-90%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinout
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
Features
- Input voltage: 9.8 to 50V
- Output voltage: 9V
- Type. maximum current: from 2.3 to 3.4 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-90%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 3 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Two M2 mounting holes
- Dimensions: 17.8 x 20.3 x 8.8 mm
Parameters
Kit contains
- D36V28F9 converter module
- Straight 6-pin goldpin connector
- 5-pin angled goldpin connector
586591
Data sheet
- Output voltage
- 9 V
- Output current
- 2,6 V
- Converter type
- Step-down
- Supply voltage min
- 9,8 V
- Supply voltages max
- 50 V
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The Step-Up Buck Voltage Regulator module with adjustable output voltage in range of 4-25V with a input voltage range of 1.5-16V and a maximum output current of 2A. Pololu 799
zł70.17 24hAvailable quantity: 2 AvailableStep-Up converter U3V70A with an output voltage from 4.5 to 20 V, an input voltage from 2.9 to VOUT and a maximum output current of 10 A. Pololu 2890
zł111.47 Delivery date unknown No product available!
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł30.63 24hAvailable quantity: 7 AvailableA set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.01 24hAvailable quantity: 390 AvailableA set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.19 24hAvailable quantity: 291 AvailableA set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.87 24hAvailable quantity: 6 AvailableStep-Down converter D36V50F9 with an output voltage of 9 V, an input voltage from 9.9 to 50 V and a maximum output current of 7 A. Pololu 4094
zł120.88 24hAvailable quantity: 1 Available
Other products in the same category (16)
The compact (0.4″ × 0.5″) D24V5F2 synchronous buck voltage regulator takes input voltages between 3 V and 36 V and efficiently reduces them to 2.5 V while allowing for a maximum output current of 500 mA. This regulator offers typical efficiencies between 80% and 90%. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
zł28.40 6 weeks No product available!
Efficient step-down converter that reduces the input voltage from up to 45 V to a regulated output voltage range from 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in protection against reverse polarity, overload and short circuit, and the spread spectrum function reduces EMI interference. The module is equipped with an additional potentiometer for adjusting the cut-off voltage. Pololu 4872
zł80.74 24hAvailable quantity: 5 AvailableA power supply based on a DC-DC converter with a current capacity of up to 5.1 A. The input voltage can range from 5 V to 30 V, while the output voltage is adjustable from 0 V to 36 V. It has built-in WiFi communication. XY3605
zł309.47 24hAvailable quantity: 2 AvailableStep-Down converter D36V50F9 with an output voltage of 9 V, an input voltage from 9.9 to 50 V and a maximum output current of 7 A. Pololu 4094
zł120.88 24hAvailable quantity: 1 Available No product available!
DC-DC Step-Down Converter ME3116AM6G with an output voltage of 5 V, input voltage from 6 to 24 V and a maximum output current of 1 A. Dedicated to the M5Stack modules. M5Stack U125
zł20.90 24hAvailable quantity: 1 AvailableStep-Down converter with adjustable output voltage from 1.25 to 36 V, input voltage from 4 to 38 V and maximum current up to 5 A. Board equipped with a voltmeter with display
zł18.71 6 weeks No product available!
An efficient step-down converter that steps down the input voltage from as low as 45 V to a regulated output voltage range of 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in reverse polarity, overload and short circuit protection, and the spread spectrum function reduces EMI interference. Pololu 4873
zł68.63 24hAvailable quantity: 5 AvailableStep-down DC-DC converter module that converts a 12 V or 11.1 V output voltage (e.g. from a lithium battery) to a voltage in the range of 1.8 V to 5.1 V. It has a power output of up to 60 W, and with an output current of up to 18 A, the module can be used to power a 5 m WS2812 RGB LED strip. DFRobot DFR1025
zł45.92 24hAvailable quantity: 1 AvailableVRM: Voltage Regulator Module (Rev. B) is a step-down converter based on the Texas Instruments TPS54620 chipset. Input voltage in the range 5 ... 15 V, output voltage 3.3 V or 5 V. Digilent 210-156
zł99.70 4 weeks No product available!
DC-DC Step Down converter module with input voltage from 7 to 24 V and output voltage of 5 V. Can supply currents up to 4 A. DFRobot DFR0831
zł23.64 24hAvailable quantity: 2 AvailableDFR0379
zł37.27 24hAvailable quantity: 12 AvailableThis compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 7.5 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
zł24.29 24hAvailable quantity: 1 AvailableModular power supply with a power of 3 W, input voltage from 100 to 240 V and output voltage of 3.3 V. Designed for mounting on a PCB. Hi-Link HLK-PM03
zł14.90 6 weeks No product available!
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40V and efficiently reduces it to 5V with an available output current of around 15A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for powering large loads. Pololu 2881
zł459.00 24hAvailable quantity: 1 AvailableDC-DC Step-Down converter module with 5V output voltage and 1A output current. The module can be a replacement for the popular LM7805 regulator.
zł8.67 24hAvailable quantity: 78 Available
Step-Down converter D36V28F9 with an output voltage of 9 V, an input voltage from 9.8 to 50 V and a maximum output current of 3.4 A. Pololu 3785