Voltage Regulator module 9V Step-Down 5A D36V50F9
ID: 586585
5906623480388
zł156.87
Tax included
zł127.54 tax excl.
Step-Down converter D36V50F9 with an output voltage of 9 V, an input voltage from 9.9 to 50 V and a maximum output current of 7 A. Pololu 4094
Description
Step-Down converter module D36V50F9 with an output voltage of 9 V and an input voltage from 9.9 to 50 V. The maximum current load of the module is from 2.7 to 7 A and depends on the input voltage. The inverter achieves standard efficiency above 80-95%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinot
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
- VRP - provides access to the input voltage before protection against voltage reverse polarity. Can be used as an output to power other devices or the input voltage can be connected to VRP instead of VIN to bypass protection.
Features
- Input voltage: 9.9 to 50V
- Output voltage: 9V
- Type. maximum current: from 2.7 to 7 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-95%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 4 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Three mounting holes M2
- Dimensions: 25.4 x 25.4 x 9.5 mm
Parameters
Kit contains
- D36V50F9 converter module
- 12-pin straight goldpin connector
586585
Data sheet
- Output voltage
- 9 V
- Output current
- 5A
- Converter type
- Step-down
- Supply voltage min
- 9,9 V
- Supply voltages max
- 50 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The Step-Up Buck Voltage Regulator module with adjustable output voltage in range of 4-25V with a input voltage range of 1.5-16V and a maximum output current of 2A. Pololu 799
zł88.63
24h
Available quantity: 2
Available
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł29.50
24h
Available quantity: 3
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.35
24h
Available quantity: 200
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
Delivery date unknown
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.49
24h
Available quantity: 12
Available
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
zł137.49
24h
Available quantity: 1
Available
Step-Down converter D36V50F5 with an output voltage of 5 V, an input voltage from 5.5 to 50 V and a maximum output current of 8 A. Pololu 4091
zł151.14
24h
Available quantity: 2
Available
Other products in the same category (16)
DC-DC Step-Down converter module AP63203 with an output voltage of 3.3 V, an input voltage of 3.8 to 32 V and a maximum output current of 2 A. SparkFun COM-18356
zł35.65
24h
Available quantity: 3
Available
Step Down DC-DC converter module based on LM2596 circuit, input voltage 3-40V, regulated output voltage 1.5--35V
zł3.92
24h
Available quantity: 872
Available
An efficient step-down converter that reduces the input voltage to 5 V at a maximum current of 100 mA, offering high efficiency due to low quiescent current (<20 μA). It supports input voltages from 5 V to 65 V, has short circuit and overheating protection, making it a reliable and energy-efficient solution. Pololu 5363
zł22.60
24h
Available quantity: 2
Available
Step-Down converter module with input voltage from 4.75 to 23V, output voltage from 1 to 17V and output current 1.8 A (3 A instantaneous current).
zł7.70
24h
Available quantity: 31
Available
Step-Down converter with adjustable output voltage from 1.25 to 36 V, input voltage from 4 to 38 V and maximum current up to 5 A. Board equipped with a voltmeter with display
zł18.56
4 weeks
No product available!
Step-Down DC-DC converter module based on the D24V150F9 chip. Input voltage 11 ... 40V, output voltage 9V (max 15A). Pololu 2884
zł485.70
24h
Available quantity: 2
Available
The Step-Down D24V6F3 Buck Voltage Regulator module gives the output voltage of 3.3V with a wide input voltage range of 4.8-42V and a maximum output current of 600 mA. Pololu 2106
zł41.55
24h
Available quantity: 4
Available
DC-DC Step-Up converter U3V40F7 with an output voltage of 7.5 V, an input voltage of 1.3 to 7.5 V and a maximum output current of 4 A. Pololu 4014
zł44.74
24h
Available quantity: 4
Available
DFRobot DFR0205 is a compact and efficient step-down DC-DC converter module with up to 25 W of power, allowing adjustment of the supply voltage to meet the needs of various electronic components. With a voltage regulation function, a quick 5 V selection switch, and an Ovout interface, it enables simultaneous power delivery to components with different voltage requirements. Ideal for prototyping, mobile projects, automation systems, and IoT applications.
zł36.88
24h
Available quantity: 5
Available
A power supply based on a DC-DC converter with a current capacity of up to 6.1 A. The input voltage can range from 6 V to 30 V, while the output voltage is adjustable from 0 V to 36 V. Enclosure version. XYL3606S
zł193.42
24h
Available quantity: 4
Available
Step-Down DC-DC converter module based on the D36V6F12 system. Input voltage 12.2.50V, output voltage 12V (max. 600mA). Pololu 3796
zł21.44
24h
Available quantity: 1
Available
Step-Down DC-DC converter module based on the D36V6F6 chip. Input voltage 6.2..50V, output voltage 6V (max. 600mA). Pololu 3793
zł22.62
4 weeks
No product available!
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 9 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
zł22.62
4 weeks
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 9 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł86.59
4 weeks
No product available!
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 15 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
zł26.84
24h
Available quantity: 1
Available
Step-Down XL4005 converter module with adjustable output voltage in the range from 0.8 to 30 V with a wide input voltage range from 4.5 to 30 V and a maximum output current of 5 A
zł19.35
24h
Available quantity: 19
Available
Step-Down converter D36V50F9 with an output voltage of 9 V, an input voltage from 9.9 to 50 V and a maximum output current of 7 A. Pololu 4094