Voltage Regulator module 3.3V Step-Down 6.5A D36V50F3
ID: 586581
5906623480357
zł137.49
Tax included
zł111.78 tax excl.
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
Description
Step-Down converter module D36V50F3 with an output voltage of 3.3 V and an input voltage from 4.5 to 50 V. The maximum current load of the module is from 4.5 to 9.5 A and depends on the input voltage. The inverter achieves standard efficiency above 80-95%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinot
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
- VRP - provides access to the input voltage before protection against voltage reverse polarity. Can be used as an output to power other devices or the input voltage can be connected to VRP instead of VIN to bypass protection.
Features
- Input voltage: 4.5 to 50V
- Output voltage: 3.3V
- Type. maximum current: from 4.5 to 9.5 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-95%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 4 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Three mounting holes M2
- Dimensions: 25.4 x 25.4 x 9.5 mm
Parameters
Kit contains
- D36V50F3 converter module
- 12-pin straight goldpin connector
586581
Data sheet
- Output voltage
- 3,3 V
- Output current
- 6.5A
- Converter type
- Step-down
- Supply voltage min
- 4,5 V
- Supply voltages max
- 50 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Pololu 12V Step-Up Voltage Regulator U3V50F12
zł135.15
24h
Available quantity: 2
Available
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł29.50
Delivery date unknown
No product available!
Step-Down converter D36V50F6 with an output voltage of 6 V, an input voltage from 6.5 to 50 V and a maximum output current of 8 A. Pololu 4092
zł123.28
24h
Available quantity: 2
Available
Step-Down converter D36V50F12 with an output voltage of 12 V, an input voltage from 13.3 to 50 V and a maximum output current of 6.5 A. Pololu 4095
zł158.76
24h
Available quantity: 2
Available
Other products in the same category (16)
Step-Down DC-DC converter module based on the D24V150F7 chip. Input voltage 9..40V, output voltage 7.5V (max 15A). Pololu 2883
zł485.70
4 weeks
No product available!
Przetwornica DC-DC Step Down (MP1584), Uwe 4.5..28V, Uwy regulowane 0.8..20V, RoHS
zł4.77
24h
Available quantity: 28
Available
Step-Down converter D36V50F9 with an output voltage of 9 V, an input voltage from 9.9 to 50 V and a maximum output current of 7 A. Pololu 4094
zł156.87
4 weeks
No product available!
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages between 4 V and 50 V and efficiently reduces them to a lower, user-adjustable voltage set by an on-board trimmer potentiometer. It has an output voltage range of 2.5 V to 7.5 V and a maximum output current of 600 mA.
zł35.84
4 weeks
No product available!
Modular power supply with a power of 3 W, input voltage from 100 to 240 V and output voltage of 3.3 V. Designed for mounting on a PCB. Hi-Link HLK-PM03
zł14.77
4 weeks
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 3.3 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 80% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł101.88
4 weeks
No product available!
Step-Down converter with adjustable output voltage from 1.25 to 36 V, input voltage from 4 to 38 V and maximum current up to 5 A. Board equipped with a voltmeter with display
zł18.56
4 weeks
No product available!
Available
An efficient step-down converter that steps down the input voltage from as low as 45 V to a regulated output voltage range of 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.8 A. It has built-in reverse polarity, overload and short circuit protection, and the spread spectrum function reduces EMI interference. Pololu 4853
zł109.36
24h
Available quantity: 5
Available
The Step-Down D24V3F9 Buck Voltage Regulator module gives the output voltage of 9V with a wide input voltage range of 11-42V and a maximum output current of 300 mA. Pololu 2099
zł34.77
4 weeks
No product available!
Step Down converter module with an output voltage of 5 V and a maximum current of 2x2,5 A. The board is equipped with four USB connectors
zł23.59
24h
Available quantity: 5
Available
The Step-Down D24V6F12 Buck Voltage Regulator module gives the output voltage of 12V with a wide input voltage range of 15-42V and a maximum output current of 600 mA. Pololu 2109
zł34.82
4 weeks
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 6 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł88.84
4 weeks
No product available!
Step-Down converter with an output voltage of 5 V, an input voltage of 6.5 to 16 V and a maximum current of 4 A
zł12.23
24h
Available quantity: 3
Available
Step Down converter module with an output voltage of 5 V and a maximum current of 3 A. The board is equipped with two USB connectors
zł7.75
24h
Available quantity: 13
Available
The Step-Down D24V3F12 Buck Voltage Regulator module gives the output voltage of 12V with a wide input voltage range of 14.5-42V and a maximum output current of 300 mA. Pololu 2100
zł31.12
4 weeks
No product available!
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090