Voltage Regulator module 12V Step-Down 4.5A D36V50F12
ID: 586586
5906623413119
zł158.76
Tax included
zł129.07 tax excl.
Step-Down converter D36V50F12 with an output voltage of 12 V, an input voltage from 13.3 to 50 V and a maximum output current of 6.5 A. Pololu 4095
Description
Step-Down converter module D36V50F12 with an output voltage of 12 V and an input voltage from 13.3 to 50 V. The maximum current load of the module is from 2.3 to 6.5 A and depends on the input voltage. The inverter achieves standard efficiency above 80-95%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinot
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
- VRP - provides access to the input voltage before protection against voltage reverse polarity. Can be used as an output to power other devices or the input voltage can be connected to VRP instead of VIN to bypass protection.
Features
- Input voltage: 13.3 to 50V
- Output voltage: 12V
- Type. maximum current: from 2.3 to 6.5 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-95%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 4 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Three mounting holes M2
- Dimensions: 25.4 x 25.4 x 9.5 mm
Parameters
Kit contains
- D36V50F12 converter module
- 12-pin straight goldpin connector
586586
Data sheet
- Output voltage
- 12V
- Output current
- 4,5 A
- Converter type
- Step-down
- Supply voltage min
- 13,3 V
- Supply voltages max
- 50 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The Step-Up Buck Voltage Regulator module with adjustable output voltage in range of 4-25V with a input voltage range of 1.5-16V and a maximum output current of 2A. Pololu 799
zł88.63
24h
Available quantity: 2
Available
Step-Up converter U3V70F6 with an output voltage of 6 V, an input voltage from 2.9 to 6 V and a maximum output current of 10 A. Pololu 2892
zł78.97
24h
Available quantity: 2
Available
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł29.50
24h
Available quantity: 3
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.35
24h
Available quantity: 198
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
Delivery date unknown
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.49
24h
Available quantity: 12
Available
Step-Down converter D36V50F5 with an output voltage of 5 V, an input voltage from 5.5 to 50 V and a maximum output current of 8 A. Pololu 4091
zł151.14
24h
Available quantity: 2
Available
Step-Down converter D36V50F6 with an output voltage of 6 V, an input voltage from 6.5 to 50 V and a maximum output current of 8 A. Pololu 4092
zł123.28
24h
Available quantity: 2
Available
Other products in the same category (16)
Step-Down converter D36V28F5 with an output voltage of 5 V, an input voltage from 5.3 to 50 V and a maximum output current of 4 A. Pololu 3782
zł80.90
24h
Available quantity: 2
Available
The Step-Down D24V3AHV Buck Voltage Regulator module with adjustable output voltage in the range of 4-25V with a wide input voltage range of 4.5-42V and a maximum output current of 300 mA. Pololu 2102
zł30.65
24h
Available quantity: 1
Available
DC-DC Step-Up converter U3V40F7 with an output voltage of 7.5 V, an input voltage of 1.3 to 7.5 V and a maximum output current of 4 A. Pololu 4014
zł44.74
24h
Available quantity: 4
Available
Step-Down converter D36V28F7 with an output voltage of 7.5 V, an input voltage from 8 to 50 V and a maximum output current of 3.7 A. Pololu 3784
zł100.72
24h
Available quantity: 4
Available
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 9 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł86.59
4 weeks
No product available!
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
zł137.49
24h
Available quantity: 1
Available
The Step-Down D24V6F9 Buck Voltage Regulator module gives the output voltage of 9V with a wide input voltage range of 11.5-42V and a maximum output current of 600 mA. Pololu 2108
zł32.61
4 weeks
No product available!
Step-Down converter with an output voltage of 5 V, an input voltage of 7 to 26 V and a maximum current of 3 A
zł6.58
24h
Available quantity: 101
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36V and efficiently reduces it to 5V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.5A and features reverse voltage protection. Pololu 2858
zł78.11
24h
Available quantity: 3
Available
An efficient step-down converter that reduces the input voltage to 12 V at a maximum current of 100 mA, offering high efficiency due to low quiescent current (<50 μA). It supports input voltage from 12 V to 65 V, has a Power Good (PGOOD) function, an EN input for system shutdown, and short circuit and overheat protection, making it a reliable and energy-efficient solution. Pololu 5377
zł23.43
4 weeks
No product available!
The Step-Down D24V6F12 Buck Voltage Regulator module gives the output voltage of 12V with a wide input voltage range of 15-42V and a maximum output current of 600 mA. Pololu 2109
zł34.82
4 weeks
No product available!
The DC-DC Buck Converter DC5-36-TO-DC3V3-5 in SMD version is designed for direct surface mounting. With selectable output voltage and high efficiency, it is suitable for applications involving microcontrollers, IoT systems, and mobile electronic devices.
zł13.65
24h
Available quantity: 5
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36 V and efficiently reduces it to 9 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.3 A and features reverse voltage protection.
zł87.23
4 weeks
No product available!
Step-Down RT8272 converter with adjustable output voltage in the range from 5 V to 12 V, input voltage from 5 to 24 V and a maximum output current of 3 A
zł9.23
24h
Available quantity: 14
Available
The compact (0.4″ × 0.5″) D24V5F15 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 15 V while allowing for a maximum output current of 500 mA. Pololu 2847
zł35.76
24h
Available quantity: 1
Available
Step-Down converter D36V50F12 with an output voltage of 12 V, an input voltage from 13.3 to 50 V and a maximum output current of 6.5 A. Pololu 4095