![WEP 992DA + WEP 992DA +](https://kamami.pl/22890-large_default/wep-992da-soldering-station.jpg)
![WEP 992DA + WEP 992DA +](https://kamami.pl/22890-large_default/wep-992da-soldering-station.jpg)
zł942.87 tax excl.
soldering iron WEP 992DA + is a hot air soldering station and a soldering iron. It is equipped with a PID microprocessor, used for soldering and desoldering electronic components, shrinking, welding plastics, heating. WEP 992DA + 3in1
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
WEP 992DA + soldering station is suitable for soldering and desoldering electronic components such as: SOIC, CHIP, QFP, PLCC, BGA, SMD, etc. (especially mobile phones).
WEP 992DA + soldering iron is a hot air soldering station and soldering iron. The station is equipped with a PID microprocessor, which checks the station operation parameters in 20ms cycles and corrects them to the set values.
Temperature values, airflow power, operating mode are visible on a large, readable LCD display, which greatly simplifies the work.
The hotair soldering iron is equipped with a ceramic heating element that quickly and evenly heats up. The heater is made of hard alloys, allowing long working time at high temperatures, without being subject to deformation, this significantly increases the stability of work and extends the life of the heater.
In the holder for the hot air flask there is a micro-contact which, when the flask is put down, causes it to go into standby mode, by cooling the heating element, and then switching off the air flow. This extends the life of the heater and saves electricity.
The station is equipped with functions to control proper operation, we receive messages about short circuit in the circuit, overload of circuits, failure to obtain the set temperature. All these errors are displayed on the display.
Selecting the automatic operation mode, when we put the hot air flask on the stand, the device will automatically stop heating and will cool down to a safe temperature. Thanks to this, we will take care of the long, trouble-free operation of the heating element, energy savings and security of the service.
The soldering iron is distinguished by such functions:
Soldering station 5 in 1: hotair (100-480 deg. C), soldering tip 60W, service power supply 0-15V / 1A, RF signal tester and voltage meter. Included, among others set of nozzles and gripper for integrated circuits
Hotair soldering station 100..480 deg. C, soldering tip 75W 200..480 deg. C. Settings are displayed on LED displays
No product available!
Station with two separate panels for a 75W (200-480 deg. C) soldering gun and hotair (100-480 deg. C).
YATO 18 V drill/driver equipped with speed regulation. It has a built-in LED light, a 4-stage battery indicator and protection against overheating. It is suitable for drilling in metal and wood, as well as for driving screws. Yato YT-82782
No product available!
The cable locator detects Ethernet, telephone and power cables. It consists of a transmitter and a receiver. It is the recommended tool for detecting communication cables and A/V cables faults. Uni-T UT682
The most popular Sn60Pb40 SW26 solder is a high-quality lead product with SW26 flux, intended for professional soldering in electronics and electrical engineering, meeting the EN ISO 9453:2014 standard
No product available!
No product available!
High-voltage differential probe. It has good measurement characteristics: a bandwidth of 100 MHz and an operating voltage of up to 1300 V. The probe has two attenuation coefficients: 50X and 500X. Hantek HT8100
The clamp meter can measure DC voltage, AC voltage and current, capacitance, frequency, temperature and resistance. Equipped with diode test function, circuit continuity test and NCV test. Aneng ST193
The universal multimeter allows you to measure direct and alternating voltage up to 600 V, direct current up to 10 A, capacity and resistance. Equipped with diode tester, circuit continuity test, backlight and overload protection. Uni-T UT133B
Universal set of tools for building a LAN network. Lanberg NT-0301
75W soldering station, temperature 200..480 degrees C.
QUICK TSS02-SK soldering tip for TS1200
No product available!
The Uni-T non-contact thermometer is designed to measure the temperature of the human body. It allows you to measure the temperature in a non-invasive way in the range from 32°C to 42.9°C from a distance of 5 to 10 cm. Uni-T UT300H
No product available!
Universal organizer with dividers. It allows you to store small parts and components. Kistenberg KTG20154
No product available!
Isopropanol 70% (IPA) is an effective and safe cleaner with low electrical conductivity, supplied in a 1l plastic bottle, perfect for professional electronics workshop thanks to its degreasing properties, fast evaporation and precise dosing
Precision screwdriver with a hardened, sand-blasted, magnetic tip.
WXP 120 soldering iron, 120W, 24V power supply. Designed for the Weller station of the WX series. Weller WXP 120
No product available!
soldering iron WEP 992DA + is a hot air soldering station and a soldering iron. It is equipped with a PID microprocessor, used for soldering and desoldering electronic components, shrinking, welding plastics, heating. WEP 992DA + 3in1