Category: STARTER KITS, PROGRAMMERS, MODULES
Kamami.pl electronics store offers a wide range of starter kits for microcontrollers and programmable devices as well as accessories (programmers, modules, etc.).
Subcategories
-
Atmel SAM
-
Atmel Xplain
-
AVR
-
Banana Pi
-
BeagleBone
-
chipKIT
-
CPLD Xilinx
-
Cubieboard
-
DFRobot FireBeetle
-
Analog electronics
-
Feather
-
Alchitry FPGA
-
Altera FPGA
-
Xilinx FPGAs
-
Freedom (Kinetis)
-
FriendlyELEC
-
Coral
-
HummingBoard
-
Other development kits
-
Intelligent clothes
-
LattePanda
-
LPC (NXP)
-
M5Stack
-
Micro:bit
-
Peripheral modules
-
Nvidia Jetson
-
Odroid
-
ODYSSEY
-
Orange Pi
-
PIC
-
Segger programmers
-
Universal programmers
-
Raisonance
-
Raspberry Pi RP2040
-
RFID
-
RISC-V
-
SBC Embest
-
SBC MYIR
-
SBC UDOO
-
SBC others
-
SoMLabs
-
Sparkfun MicroMod
-
STM32
-
STM32 MP1
-
STM32 Discovery
-
STM32 Nucleo boards
-
STM8
-
Teensy
-
WRTNode
-
Kit with a book
There are 2485 products.
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
Four relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
The Raspberry Pi Debug Probe is an affordable tool that combines a USB-UART debugger and converter. Includes the necessary hardware and wiring needed to quickly debug the Raspberry Pi Pico, RP2040 microcontrollers, and other ARM Cortex-based MCUs. Raspberry Pi SC0889
Extruded aluminium heatsink with pins, dedicated to SLC5 single board computer (TitanSBC-8Mmini). Thermal resistance 15.2K/W, maximum dissipation loss 4.2W
KAmodDIGIpot is a miniature digital potentiometer module. It allows, by means of two PU / PD inputs, to change the resistance value between the outputs A, W, B (compatible with the outputs of the analog potentiometer), using buttons or outputs of the microcontroller. Adjustment in 32 steps, value 10k.
Module with digital thermal sensor, thermostat and I2C interface
VisionSOM-6ULL is comprised of a small processor module with CPU bus accessibility and standard I/O functionality and is an ideal solution for embedded projects.
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
Module with AT42QT1060 controller - contectless keyboard controller, Kamami, RoHS.
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
Module from the VisionSOM series with NXP i.MX RT1052 microcontroller (Cortex-M7 core), 528MHz, QSPI 16MB memory, 32MB SDRAM memory, -40 .. + 85 ° C.
SLS12RT52_528C_32R_16QSPI_0SF_I
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Raspberry Pi Pico
WiFi 802.11 b/g/n module with ESP8266 system, they have 22 edge terminals with 2 mm raster with the possibility of soldered gold connectors, 9 GPIO lines and 1 ADC line on the connector. Built-in PCB antenna. ESP-12E
The RFID / NFC transponder reader module (tags) works in the PN532 chip and is compatible with Arduino. Data is available via SPI, I2C or HSU (High Speed UART). Supplied with a RFID card and key ring. ELECHOUSE NFC MODULE V3
Programmer-configurator PLD (CPLD and FPGA) from Altera, compatible with Altera USB Blaster Download Cable. It supports Altera JTAG and ISP/ICP interfaces.
A colour camera module with a resolution of 5 MPx. It is equipped with a MIPI-CSI interface and an FPC30 connector, making it compatible with SoMLabs base boards. SoMLabs SL-MIPI-CSI-OV5640
STM32 Nucleo-144 development board with STM32F746ZGT6 MCU, supports Arduino, ST Zio and Morpho
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20