TFT LCD display with a diagonal of 3.5" and a resolution of 480x320 pixels. Equipped with a resistive touch panel and a microSD slot. Intended for use with Feather series boards. Adafruit 3651

DFRobot BLE4.1 Module is a Bluetooth 4.1 module with DA14681 processor with 3.3 V power supply. It is characterized by low energy consumption and advanced energy management system (built-in charging module). DFRobot TEL0120

Arducam USB shield is a module that allows you to connect some ArduCam cameras to a PC or minicomputers, eg Raspberry Pi, BeagleBone etc. The module supports most cameras with a serial interface that have a resolution of 0.3 ... 14 MPix. Attached to the module are appropriate libraries that facilitate image processing, eg using OpenCV software. ArduCam B0095

Camera module with Sony IMX219 sensor works with all versions of Raspberry Pi. The camera is equipped with a matrix with a resolution of 8 MPx, the maximum video resolution is 1080p. ArduCAM B0102

DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. Polol 2133

Evaluation set designed for the use of Internet of Things based on ArduCAM-Mini-2MP and ArduCAM-ESP8266-Nano-V2 modules. ArduCAM-Mini-2MP is a module with a 2 megapixel camera with an OV2640 transducer and an ESP8266 chip. Mounting the M12 lens. ArduCAM B0085

TFT 2.4 "display module with SD, 240x320, touch panel, ILI9341, RoHS

Step-Down DC-DC converter module based on the D24V150F12 chip. Input voltage 14.5 ... 40V, output voltage 12V (max 15A). Pololu 2885

This module features a fixed-gain, 38 kHz modulated IR sensor and a corresponding IR LED with oscillator circuit to make a tiny proximity sensor. This low-brightness version draws an average of 8 mA at 5 V and has a typical sensing range up to approximately 12 inches (30 cm).

Analog pH Meter Pro (SEN0169)

The MAX31865 amplifier module is an ideal tool for accurate temperature measurement in various applications. It is compatible with 2, 3 or 4-wire PT100 RTD temperature probes. Adafruit 3328

Gravity: 360 Degree Hall Angle Sensor is a rotation angle sensor measuring a value in the range of 0-360 ° with an analogue output, powered by 5V. DFRobot SEN0221

LCD TFT display with a diagonal of 2.4 "and a resolution of 320x240 pixels. Equipped with a resistive touch panel and microSD slot. Designed for use with Feather series plates. Adafruit 3315

This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40V and efficiently reduces it to 5V with an available output current of around 15A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for powering large loads. Pololu 2881

This add-on board makes it easy to control two high-power DC motors with a Raspberry Pi. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 Voperating range and are efficient enough to deliver a continuous 18 A without a heat sink. The drivers offer basic current limiting functionality, and they accept ultrasonic PWM frequencies for quieter operation. 

This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.

Ultrasonic distance sensor with a measuring range of 2 to 400 cm. Communicates via a standard interface (Echo, Trigger) or I2C bus. SparkFun SEN-24805

A new version of the popular mono amplifier kit, capable of amplifying audio from any source, such as MP3 players, using the NCP2890 with an output power of up to 1 W. The kit comes pre-assembled, including a jack cable, 8Ω speaker, and a battery holder for two AA batteries, allowing for quick start-up and ideal for portable DIY audio projects. Kitronik 2165B