zł353.21 tax excl.
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40V and efficiently reduces it to 5V with an available output current of around 15A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for powering large loads. Pololu 2881
The D24V150Fx family of step-down voltage regulators are high-current synchronous switching regulators that generate lower output voltages from input voltages as high as 40V. These types of regulators are also known as switched-mode power supplies (SMPS) or DC-to-DC converters, and they are much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. In particular, the D24V150Fx family of regulators have typical efficiencies of 80% to 95%, depending on factors like input voltage, output voltage, and load.
These regulators have an instantaneous current limit of approximately 32A, but they are limited in the long term to much lower currents by power dissipation and the corresponding temperature rise that induces in the board. The regulators can typically support continuous output currents between 5A and 20A without additional cooling (such as with a heat sink or forced airflow), depending on the input voltage and output voltage. In general, the available output current is a little higher for the lower-voltage versions than it is for the higher-voltage versions, and it decreases as the input voltage increases.
These regulators have a typical quiescent (no load) current draw of around 100mA, and an enable pin can be used to put the boards in a low-power state that reduces the quiescent current to approximately 5µA to 10µA per volt on VIN.
The modules have built-in reverse-voltage protection, short-circuit protection, a thermal shutdown feature that helps prevent damage from overheating, and a soft-start feature that reduces inrush current. They also feature undervoltage lockout that disables the regulator if the input voltage falls below about 3.5 V.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 3.3 V with an available output current of around 15 A. Pololu 2880
No product available!
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 6 V with an available output current of around 15 A. Pololu 2882
No product available!
Step-down DC-DC converter module that converts a 12 V or 11.1 V output voltage (e.g. from a lithium battery) to a voltage in the range of 1.8 V to 5.1 V. It has a power output of up to 60 W, and with an output current of up to 18 A, the module can be used to power a 5 m WS2812 RGB LED strip. DFRobot DFR1025
Waterproof DC-DC Step-Down Converter with 8 to 22V input voltage and 5V 3A USB output
No product available!
A power supply based on a DC-DC converter with a current capacity of up to 5.1 A. The input voltage can range from 5 V to 30 V, while the output voltage is adjustable from 0 V to 36 V. It has built-in WiFi communication. XY3605
The Step-Down D24V3F3 Buck Voltage Regulator module gives the output voltage of 3,3V with a wide input voltage range of 4.3-42V and a maximum output current of 300 mA. Pololu 2097
Step Down DC-DC converter module based on LM2596 circuit, input voltage 3-40V, regulated output voltage 1.5--35V
No product available!
The compact (0.4″ × 0.5″) D24V5F15 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 15 V while allowing for a maximum output current of 500 mA. Pololu 2847
No product available!
Step-Down converter with an output voltage of 5 V, an input voltage of 7 to 26 V and a maximum current of 3 A
An efficient step-down converter that reduces the input voltage to 5 V at a maximum current of 100 mA, offering high efficiency due to low quiescent current (<20 μA). It supports input voltages from 5 V to 65 V, has short circuit and overheating protection, making it a reliable and energy-efficient solution. Pololu 5363
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 7.5 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
Step-Down XL4005 converter module with adjustable output voltage in the range from 0.8 to 30 V with a wide input voltage range from 4.5 to 30 V and a maximum output current of 5 A
A power supply based on a DC-DC converter with a current capacity of up to 5.1 A. The input voltage can range from 5 V to 30 V, while the output voltage is adjustable from 0 V to 36 V. XY3605
DFRobot DFR0205 is a compact and efficient step-down DC-DC converter module with up to 25 W of power, allowing adjustment of the supply voltage to meet the needs of various electronic components. With a voltage regulation function, a quick 5 V selection switch, and an Ovout interface, it enables simultaneous power delivery to components with different voltage requirements. Ideal for prototyping, mobile projects, automation systems, and IoT applications.
No product available!
The Step-Up Buck Voltage Regulator module with output voltage of 3.3V and input voltage range of 1-3V and a maximum output current of 200 mA. STMicroelectronics EVAL4971
DFR0379
This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40V and efficiently reduces it to 5V with an available output current of around 15A. Typical efficiencies of 80% to 95% along with its high current capabilities make this regulator well suited for powering large loads. Pololu 2881