Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3
search
  • Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3
  • Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3
  • Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3 - widok od góry
  • Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3 - widok od spodu
  • Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3 - wyprowadzenia
  • Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3 - wymiary
  • Moduł przetwornicy DC-DC Step-Down 4.5...40V - 3.3V D24V150F3
ID: 563264
zł463.29
Tax included

zł376.66 tax excl.

This synchronous switching step-down (or buck) regulator takes an input voltage of up to 40 V and efficiently reduces it to 3.3 V with an available output current of around 15 A. Pololu 2880

4 weeks
On request
Pololu 15A D24V150 converters, voltage:
4,5-40 / 3,3 V
6-40 / 5 V 7,2-40 / 6 V 9-40 / 7,5 V 11-40 / 9 V 14,5-40 / 12 V
Kamami is the official distributor of electronic modules and Pololu robotic parts. All products of this brand in our offer are original and come directly from the manufacturer.

Description

The D24V150Fx family of step-down voltage regulators are high-current synchronous switching regulators that generate lower output voltages from input voltages as high as 40V. These types of regulators are also known as switched-mode power supplies (SMPS) or DC-to-DC converters, and they are much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. In particular, the D24V150Fx family of regulators have typical efficiencies of 80% to 95%, depending on factors like input voltage, output voltage, and load.

These regulators have an instantaneous current limit of approximately 32A, but they are limited in the long term to much lower currents by power dissipation and the corresponding temperature rise that induces in the board. The regulators can typically support continuous output currents between 5A and 20A without additional cooling (such as with a heat sink or forced airflow), depending on the input voltage and output voltage. In general, the available output current is a little higher for the lower-voltage versions than it is for the higher-voltage versions, and it decreases as the input voltage increases.

These regulators have a typical quiescent (no load) current draw of around 100mA, and an enable pin can be used to put the boards in a low-power state that reduces the quiescent current to approximately 5µA to 10µA per volt on VIN.

During normal operation, this product can get hot enough to burn you. Even with very light loads, the regulator can run very hot if the input voltage is high, and the higher the input voltage the hotter the regulator will run. Take care when handling this product or other components connected to it.

The modules have built-in reverse-voltage protection, short-circuit protection, a thermal shutdown feature that helps prevent damage from overheating, and a soft-start feature that reduces inrush current. They also feature undervoltage lockout that disables the regulator if the input voltage falls below about 3.5V.

Features

  • Input voltage:
    • 4.5V to 40V for the version that outputs 3.3V
    • [output voltage + dropout voltage] to 40V for output voltages of 5V and higher (see below for more information on dropout voltage)
  • Fixed 3.3V, 5V, 6V, 7.5V, 9V, or 12V output (depending on regulator version) with 4% accuracy
  • Typical maximum continuous output current between 5A and 20A
  • Typical efficiency of 80% to 95%, depending on input voltage, output voltage, and load
  • Integrated reverse-voltage protection, over-current protection, over-temperature shutoff, undervoltage lockout, and soft-start
  • Typical no-load quiescent current of 100mA ; this can be reduced to approximately 5µA to 10µA per volt on VIN by disabling the board
  • “Power good” output indicates when the regulator cannot adequately maintain the output voltage
  • Compact size: 1.7″ × 1.25″ × 0.43″ (43.2mm × 31.8mm × 11mm)
  • Four 0.086″ mounting holes for #2 or M2 screws
563264

Data sheet

Output voltage
3,3 V
Output current
15 A
Converter type
Step-down
Supply voltage min
4,5 V
Supply voltages max
40 V

Manufacturer

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

Responsible person

  • BTC Korporacja sp. z o. o.
  • Ludwinowo Zegrzyńskie 52G
  • 05-140 Ludwinowo Zegrzyńskie
  • Poland
  • [email protected]
  • 22 767 36 20

You might also like

Other products in the same category (16)