Voltage Regulator module 6V Step-Down 2.7A D36V28F6
ID: 586589
5906623480395
zł112.72
Tax included
zł91.64 tax excl.
Step-Down converter D36V28F6 with an output voltage of 6 V, an input voltage from 6.3 to 50 V and a maximum output current of 4 A. Pololu 3783
Description
Step-Down converter module D36V28F6 with an output voltage of 6 V and an input voltage from 6.3 to 50 V. The maximum current load of the module is from 2 to 4 A and depends on the input voltage. The inverter achieves a standard efficiency of over 80-90%, which is dependent on the input voltage and load. The module is protected against reverse polarity, overheating, overload and short circuit.
Pinout
- VIN - power input
- GND - ground
- VOUT - output
- PG - an open drain output that goes low when the regulator's output voltage rises more than 20% above or drops by more than 10% below the nominal voltage
- EN - converter is enabled by default (100 kΩ pull-up resistor on the board connects EN pin with VIN). The ENABLE pin can be set low to turn off the power and put the board into a low-power state.
Features
- Input voltage: 6.3 to 50V
- Output voltage: 6V
- Type. maximum current: from 2 to 4 A
- Built-in protection against overheating, overload, short circuit and reverse polarity
- Type. efficiency: 80-90%
- Switching frequency: approx. 500 kHz under heavy loads
- Energy saving mode
- Typical quiescent current from 2 mA to 3 mA
- EN input with a precise cut-off threshold to disconnect the load and put the controller into a low-power state
- Power good output, which indicates when the controller cannot maintain the output voltage adequately
- The soft-start function limits the inrush current and gradually increases the output voltage
- Two M2 mounting holes
- Dimensions: 17.8 x 20.3 x 8.8 mm
Parameters
Kit contains
- D36V28F6 converter module
- Straight 6-pin goldpin connector
- 5-pin angled goldpin connector
586589
Data sheet
- Output voltage
- 6.0V
- Output current
- 2,7 A
- Converter type
- Step-down
- Supply voltage min
- 6,3 V
- Supply voltages max
- 50 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
The Step-Up Buck Voltage Regulator module with adjustable output voltage in range of 4-25V with a input voltage range of 1.5-16V and a maximum output current of 2A. Pololu 799
zł88.63
24h
Available quantity: 2
Available
Step-Up converter U3V70A with an output voltage from 4.5 to 20 V, an input voltage from 2.9 to VOUT and a maximum output current of 10 A. Pololu 2890
zł112.24
Delivery date unknown
No product available!
The trigger module is designed for chargers PD 2.0 and PD 3.0. It is equipped with a USB type C input and an output on a 5.08 mm ARK screw connector. Allows you to power devices with 5 V, 9 V, 12 V, 15 V and 20 V and test chargers by replacing the PD device
zł29.50
24h
Available quantity: 6
Available
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.35
24h
Available quantity: 207
Available
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
Delivery date unknown
No product available!
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.49
24h
Available quantity: 17
Available
Step-Down converter D36V50F6 with an output voltage of 6 V, an input voltage from 6.5 to 50 V and a maximum output current of 8 A. Pololu 4092
zł123.28
24h
Available quantity: 2
Available
Other products in the same category (16)
Modular power supply with a power of 3 W, input voltage from 100 to 240 V and output voltage of 5 V. Designed for mounting on a PCB. Hi-Link HLK-PM01
zł14.90
4 weeks
No product available!
Efficient step-down converter that reduces the input voltage from up to 45 V to a regulated output voltage range from 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.8 A. It has built-in protection against reverse polarity, overload and short circuit, and the spread spectrum function reduces EMI interference. The module is equipped with an additional potentiometer for adjusting the cut-off voltage. Pololu 4852
zł126.22
24h
Available quantity: 5
Available
DC-DC Step-Down Converter ME3116AM6G with an output voltage of 5 V, input voltage from 6 to 24 V and a maximum output current of 1 A. Dedicated to the M5Stack modules. M5Stack U125
zł19.90
24h
Available quantity: 1
Available
The very small step-down 6 V, 2.5 A synchronous inverter can be supplied with voltage up to 36 V, dimensions: 17.8 mm x 17.8 mm. Pololu 2859
zł87.23
4 weeks
No product available!
DC-DC step-down converter module 5V 16A used to convert energy from 6-24V input voltage to stable 5V, providing up to 16A current. Thanks to high conversion efficiency (over 90%) and low ripple (<20mV), it is ideal for powering sensitive devices in applications such as robotics, drones or LED lighting systems. Additionally, built-in overheating and short-circuit protection mechanisms ensure reliable operation even in difficult conditions. DFRobot DFR1202
zł56.40
24h
Available quantity: 6
Available
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 9 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
zł22.62
4 weeks
No product available!
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 6 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł88.84
4 weeks
No product available!
No product available!
Step-Down RT8272 converter with adjustable output voltage in the range from 5 V to 12 V, input voltage from 5 to 24 V and a maximum output current of 3 A
zł9.23
24h
Available quantity: 14
Available
An efficient step-down converter that steps down the input voltage from as low as 45 V to a regulated output voltage range of 1.4 to 7 V, offering high efficiency and a maximum continuous current of 3.4 A. It has built-in reverse polarity, overload and short circuit protection, and the spread spectrum function reduces EMI interference. Pololu 4873
zł109.35
24h
Available quantity: 4
Available
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages up to 50 V and efficiently reduces them to 7.5 V while allowing for a maximum output current of 600 mA. It has a very low dropout, so it can be used with input voltages that are within a few hundred millivolts of its output.
zł26.40
4 weeks
No product available!
A power supply based on a DC-DC converter with a current capacity of up to 4 A. The input voltage can range from 5 V to 30 V, while the output voltage is adjustable from 0.5 V to 30 V. ZK-4KX
zł65.45
24h
Available quantity: 5
Available
DC-DC step-down converter module 12V 12A used to convert energy from 15-24V input voltage to stable 12V, providing up to 12A current. Thanks to high conversion efficiency (over 90%) and low ripple (<50mV), it is ideal for powering sensitive devices in applications such as robotics, drones or LED lighting systems. Additionally, built-in overheating and short-circuit protection mechanisms ensure reliable operation even in difficult conditions. DFRobot DFR1208
zł68.94
24h
Available quantity: 4
Available
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 7.5 V. The board measures only 0.7″ × 0.7″, but it allows a typical continuous output current of up to 2.5 A. Typical efficiencies of 85% to 95% make this regulator well suited for powering moderate loads like sensors or small motors.
zł91.16
24h
Available quantity: 2
Available
Modular power supply with a power of 3 W, input voltage from 100 to 240 V and output voltage of 3.3 V. Designed for mounting on a PCB. Hi-Link HLK-PM03
zł14.77
4 weeks
No product available!
Step-Down converter D36V28F7 with an output voltage of 7.5 V, an input voltage from 8 to 50 V and a maximum output current of 3.7 A. Pololu 3784
zł100.72
24h
Available quantity: 4
Available
Step-Down converter D36V28F6 with an output voltage of 6 V, an input voltage from 6.3 to 50 V and a maximum output current of 4 A. Pololu 3783