Category: Main categories

Audio module with DAC and headphone amplifier designed to work with the Raspberry Pi Pico. It is based on the PCM5100A system and communicates via the I2S interface. Pimoroni PIM544

Transistor tester dedicated to work with Analog Discovery 2 and Analog Discovery (Legacy) devices. It allows you to draw the characteristics of such elements as diodes, NPN and PNP transistors as well as P and N FET transistors. Digilent 410-413

GPS module with GNSS receiver ZED-F9P. It can receive data from GPS, GLONASS, Galileo and BeiDou systems. It has USB, UART, I2C and SPI interfaces. RTK and high accuracy up to 10 mm. SparkFun GPS-15136

Step-Down XL4015 converter module with adjustable output voltage in the range from 1.25 to 33 V with a wide input voltage range from 4 to 35 V and a maximum output current of 5 A

Step-Down converter with adjustable output voltage from 1.25 to 36 V, input voltage from 4 to 38 V and maximum current up to 5 A. Board equipped with a voltmeter with display

The shield allows for easier connection of cables to the Arduino UNO R3 board. Thanks to the screw connectors, it is possible to fast and secure the cable, goldpin connectors allow you to easily connect the servo, and the built-in female connectors allow you to put additional Arduino shields

Programmable, linear laboratory power supply with adjustable supply voltage up to 32 V and current up to 3 A. The power supply has two output channels 32V/3A and one channel 5V/3A. Uni-T UTP3303

Flexible extension for a microSD card with a length of 25 cm. Supports all capacities and card types, including: 16 GB, 32 GB, 64 GB, 128 GB Micro SD/SDHC.

Evaluation kit with Bluetooth 5.0 Sparkfun Artemis module. Equipped with a microphone, kmaers and accelerometer. Himax HM01B0 camera included. SparkFun KIT-17071

SATA III to USB 3.0 adapter. It allows you to connect a 2.5" HDD, 3.5" HDD or SSD to a computer via USB. The angle joint facilitates assembly

SATA III to USB 3.0 adapter. It allows you to connect a 2.5" HDD, 3.5" HDD or SSD to a computer via USB. Comes with a 12 V power supply

Step-Up/Step-Down converter with adjustable output voltage from 0.8 to 33 V, input voltage from 4.5 to 30 V and a maximum current of 5 A. It is equipped with a voltmeter with a display

Step-Up converter module with adjustable output voltage in the range from 3 to 30 V with a wide input voltage range from 2 to 24 V and a maximum output current of 4 A. The board is equipped with a USB connector

A computer adapter (USB, Ethernet, WiFi) that works as a 2-channel oscilloscope, a 16-channel logic analyzer and a programmable signal generator. Includes BNC oscilloscope probes. Digilent 471-041

Module with bipolar stepper motor driver TC78H670FTG. It allows you to control the motor with an accuracy of 1/128 of a step with a voltage from 3.6 to 16 V and a current of up to 2 A. SparkFun ROB-16836

A set with a development board with the nRF51822 chip, designed for learning programming for pupils and students. It is a more extensive alternative to micro:bit educational modules. DFRrobot DFR0840

Extension module for Raspberry Pi. It allows you to control two DC motors, support encoders, 4 servos, IMU 9DoF and connect Qwiic modules. SparkFun ROB-16328

Integrated BME688 gas, pressure, temperature and humidity sensor in one MEMS housing. The system can be supplied with the voltage of 3.3 V and is equipped with an I2C communication interface. BME688 Breakout Board

Lens with CS-mount and 3.2 mm focal length with a very wide angle of view of 120°. Designed to work with the Raspberry Pi HQ camera. ArduCAM LN051

A computer adapter (USB, Ethernet, WiFi) that works as a 4-channel oscilloscope, a 16-channel logic analyzer and a programmable signal generator. Digilent 410-394