Category: Main categories

Miniature (25x40mm) WiFi b / g / n module with 2.0mm goldpin connection with TCP and UDP protocols operating in standalone and access point mode. The module is equipped with UART and Ethernet interfaces, it is also possible to control GPIO lines. Powered by 3.3V. HF-A11-1

IPS LCD display with a diagonal of 5" and a resolution of 800x480 pixels, equipped with a capacitive touch panel. Communicates via the RGB interface. With a mounting frame. Riverdi RVT50HQTFWCA0

A set with a 64 MP camera and a 2 DOF control platform designed for Raspberry Pi minicomputers. The camera has an integrated IR filter and autofocus. The control platform is based on two digital servos that allow you to control the position of the camera in two dimensions. ArduCAM B0399B0283

A set with a 64 MP camera and an Ethernet adapter designed for minicomputers Raspberry Pi and Jetson Nano. It allows you to extend the connection range between the minicomputer and the camera up to 15 m. ArduCAM B0399U6248

BMS protection module designed for 7 Li-Ion cells. It has a charging function with balancer option and an over-discharge protection function. Dedicated to an electric bicycle or scooter

GPIO expansion board for Raspberry PI B + and RPi 2 - set: cable, adapter, contact pad 400 fields

STM32 Nucleo-64 development board with STM32F303RET6 MCU, supports Arduino and ST morpho connectivity

Set with a camera with a resolution of 108 MP, USB 3.0 adapter and a cable. ArduCAM EK030

A DC-DC voltage converter, based on a combination of an LM2577S Step-Up converter and an LM2596S Step-Down converter. The input voltage can range from 3.5 V to 28 V, and the output voltage is adjustable from 1.25 V to 26 V

DC-AC converter, also referred to as an inverter. Converts a constant voltage (DC) of 12 V to an alternating voltage (AC) of 220 V

DC-AC converter, also referred to as an inverter. It converts a constant voltage (DC) of 12 V to an alternating voltage (AC) of 110 V, 200 V, 220 V or 280 V

BMS protection module designed for 10 Li-Ion cells. It has a charging function with balancer option and an over-discharge protection function. Dedicated to an electric bicycle or scooter

Quadruple programmable frequency generator by Silicon Labs in the range of 5 to 350MHz. Communication with the system can take place via the I2C bus. The system is housed in the QFN24 housing

Single operational amplifier STMicroelectronics LMV321LILT type Rail-to-Rail. It is designed to work with low supply voltages (supply voltage range 2.7V-5V), the maximum current consumption of the system is 250uA (at 5V voltage). System in the SOT23-5 housing

32-bit microcontroller from the STM32F4 family with ARM Cortex-M4 core, 256kB Flash, 128KB SRAM, I2C, HDMI-CEC, Irda, LIN, SPI, UART / USART, USB, DMA, PWM, 1.7 ... 3.6V, LQFP-100

Module with e-Paper display, 3.52" diagonal and 360x240 px resolution. Communication via SPI interface. Waveshare 3.52inch e-Paper HAT

QLED IPS 15.6" display with touch panel and Quantum Dot technology. Equipped with HDMI interface for image display and USB for touch panel. Resolution 1920x1080 pixels. Waveshare 15.6HP-CAPQLED-EU

Adjustable proximity sensor E18-D50NK allows detection of the object within 3 - 50 cm. Detection of an obstacle occurs due to the appearance of reflected infrared light.

15.6" portable touch screen monitor. Equipped with HDMI and USB Type-C interface for image display and USB Type-C for touch screen operation. High resolution 1920x1080 pixels and HDR technology. Waveshare 15.6inch FHD LCD (B) (EU )

ARK terminal connector spring 2-pin, pitch 3.5 mm, non-detachable.