modL293D
ID: 204176
5906623440603
zł9.45
Tax included
zł7.68 tax excl.
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
modL293D - Motor control shield for Arduino
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS
It contains two L293D motor drivers and one 74HC595 shift register. The shift register expands 3 pins of the Arduino to 8 pins to control the direction for the motor drivers. The output enable of the L293D is directly connected to PWM outputs of the Arduino.
Features
- 2 connections for 5V hobby servos connected to the Arduinos high-resolution dedicated timer - no jitter!
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- Pull down resistors keep motors disabled during power-up
- Big terminal block connectors to easily hook up wires (18-26AWG) and power
- Arduino reset button brought up top
- 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
- Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO
Download
204176
Data sheet
- Output current
- 0.6A
- Number of channels
- 4
- Supply voltage min
- 4,5 V
- Supply voltages max
- 25 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
Delivery date unknown
No product available!
A set with ATmega2560 microcontroller (256 kB Flash, 8 kB RAM, 4 kB EEPROM) clocked at 16 MHz. The user has, among others: 54 I / O lines, 14 PWM channels, 16 analog inputs. Arduino A000067
zł189.00
24h
Available quantity: 26
Available
Other products in the same category (16)
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2981
zł47.48
24h
Available quantity: 2
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5038
zł302.09
4 weeks
No product available!
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini
zł45.61
24h
Available quantity: 3
Available
The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548
zł84.92
24h
Available quantity: 2
Available
2x1.2A DC Motor Driver is a dual controller of DC motors powered with 2.5 ... 12V voltage with a maximum current consumption of 1.2A (3.2A peak) per channel. DFRobot DRI0044
zł20.82
24h
Available quantity: 6
Available
Stepper motor driver with MP6500 system with a potentiometer for current regulation. It allows the bipolar motor to be supplied with current up to 1.5A per phase without the use of a heat sink. Pololu 2967
zł49.20
4 weeks
No product available!
The high power motor driver module works on the basis of Infineon BTS7960B systems. Maximum controller current: 43 A, operating voltage range: 5.5V - 27V. The module has a heat sink and can be controlled from the Arduino, Raspberry Pi, and STM levels. IBT_2
zł39.30
24h
Available quantity: 28
Available
Motoron M3S256 Triple Motor Controller Shield - 3-channel DC motor driver for Arduino (for assembly)
DC motor driver that allows you to control the movement of three drives using the I2C interface. Plate with connectors for assembly. Pololu 5031
zł202.77
4 weeks
No product available!
Stepper motor driver based on TB67S249FTG. It allows you to control a stepper motor with voltage from 10 to 47V, with a maximum current of 1.8A. The controller can be controlled using: USB, Serial TTL, I2C, RC (PWM modeling), analog input or quadrature encoder. Pololu 3138
zł252.80
24h
Available quantity: 1
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5058
zł431.43
4 weeks
No product available!
Pololu Jrk 12v12 USB Motor Controller with Feedback
zł977.65
24h
Available quantity: 2
Available
Powerful DC motor driver. It allows you to control a motor with a power supply voltage in the range of 6 ... 28 V, the motor can draw current of 100 A (using a heat sink). For the control PWM modeling (eg from RC receivers) is used in robotics, small electric vehicles or wherever there is a need to control a DC motor. Digilent 410-334-1
zł467.81
3 weeks
No product available!
Module of a 4-channel driver of DC motors with RP2040 microcontroller. It allows the connection of encoders and is equipped with a QW/ST connector. Pimoroni PIM636
zł146.07
24h
Available quantity: 4
Available
MP6500 Stepper Motor Driver Carrier, Digital Current Control
zł44.44
24h
Available quantity: 1
Available
Two-channel DC motor driver powered with the voltage from 2.5 to 12 V with a maximum continuous current of 0.8 A per channel. It can control a bipolar stepper motor
zł4.08
24h
Available quantity: 64
Available
Stepper motor driver that can work with a voltage in the range from 20 to 50 V and a maximum current of 5.6 A. It allows you to configure the microstep in the range from 2 to 128. DM556
zł76.85
24h
Available quantity: 17
Available
Motor-driven expansion board for Arduino, L293D, 74HC595 shift register, RoHS