TPA3110D2 2x15W stereo audio amplifier with Bluetooth module

Class A audio amplifier with one channel, 25 W. Built on the popular design of J. Hood from 1969. The set includes 2 pieces

Digital audio amplifier dedicated to woofers. It has one channel with a power of 50W and can work with speakers from 4 to 8 Ω. It is powered with the voltage from 8 to 25 V

Zeenko ZK07-BM is a low-noise, wideband amplifier with very high gain, powered by a battery and intended for operation in the 30 MHz – 6 GHz band. Ideal for compensating losses in long antenna lines, it provides up to 43 dB of gain and very good noise performance. Recommended for installation as close to the antenna as possible in receiving and measurement paths.

The 2x15W amplifier module with Bluetooth XY-P15W is a compact audio device with a wide voltage range and modern Bluetooth 5.0, enabling wireless sound transmission at a distance of up to 15 meters. Thanks to built-in protection mechanisms, it ensures not only sound quality but also safe use in audio projects.

Digital mono audio amplifier based on the HXJ8002 chip. It has one channel with a power of 3 W and can work with speakers from 2 to 8 Ω. It is powered with the voltage from 2 V to 5.5 V

Stereo audio amplifier with Bluetooth 4.2 communication. It can be powered with the voltage from 19 to 24 V and has two outputs with a power of 80 W

Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475

The TPA3116D2 amplifier module is a digital class D amplifier, offering 2x50W of power for stereo channels and 100W for the subwoofer, powered by 12V-24V. Thanks to the built-in NE5532 low-pass filter, it provides clean bass sound, and three potentiometers allow you to adjust the volume and cutoff frequency.

MP3 panel with a HiFi amplifier for installation in an audio device. It allows you to play files from USB memory, SD card, via AUX and Bluetooth. It has a built-in FM receiver

Audio module with DAC, stereo amplifier and display, designed to work with the Raspberry Pi. Pimoroni PIM484

Class D digital audio amplifier with Bluetooth 5.0 module. It has two channels with a power of 50 W and can work with speakers from 4 to 16 Ω. It is powered with the voltage ranging from 9 to 24 V.

Microphone preamplifier based on the NE5532 chip. Powered with DC voltage from 9 V to 24 V or AC in the range from 8 V to 16 V

HiFi stereo tube amplifier based on 6J1 and 6P1 tubes. Designed for use with loudspeakers up to 3 W and an impedance of 4 Ω or 8 Ω

LM386 mono digital audio amplifier module. It has a voltage gain of 200 and is powered from 5V to 12V

Zeenko ZK04-UM is a compact low-noise RF amplifier operating in the 100 kHz – 4 GHz range, powered via USB-C, featuring high linearity and low noise levels. Ideal for amplifying antenna signals or as a preamplifier for spectrum analyzers such as the tinySA ULTRA, especially above 3.5 GHz.

Class-D mono audio amplifier module based on the MAX98357 chip. It can work with a 4 to 8 ohm speaker of up to 2.5 W and communicates via an I2S interface. DFRobot DFR0954