.png)
Module with two OPA627 amplifiers
ID: 588079
5906623448463
zł24.39
Tax included
zł19.83 tax excl.
Module with two operational amplifiers OPA627
Description
A module with two OPA627 operational amplifiers connected to each other via an adapter. Amplifiers in SMD housings are placed on the upper and lower sides of the board, thanks to which they take up very little space. The outputs of both amplifiers are available on male goldpin connectors, compatible with the spacing of the pins of the DIP8 housing.
Features
- 2 x OPA627 amplifier
- SO8 to DIP8 adapter
- Supply voltage: 4.5 to 18 V
- Low noise level
- Offset voltage: 100uV
- Drift: 0.8uV/C
- 16MHz bandwidth
- 55V/us conversion rate
- Distortion 0.0006%
- Current consumption: 7.5 mA
588079
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
SOP8 / SOIC8 adapter on DIP8 in the form of a PCB. It will be used as a programmer adapter, contact plates or prototype structures.
zł1.50
24h
Available quantity: 42
Available
Adapter with two DIP8 sockets and one DIP8 male connector
zł8.43
24h
Available quantity: 8
Available
Other products in the same category (16)
BOB-11044 OSHWTPA2005D1 class D audio amplifier module. The chip can work with a loudspeaker up to 1.4 W and 8 Ohm. SparkFun BOB-1104
zł41.91
24h
Available quantity: 2
Available
Available
Available
No product available!
The board has a class D amplifier onboard that can drive 2 channels of 4-8 ohm impedance speakers at 20W each. Adafruit 1752
zł108.13
24h
Available quantity: 4
Available
Analog input/output module used for testing the integrated AD/DA function of MCUs
zł18.38
24h
Available quantity: 3
Available
Sound terminal expansion board based on STA350BW for STM32 Nucleo
zł194.73
1 weeks
No product available!
Audio module with 8 Ohm loudspeaker and 8002B amplifier. It can be used as a buzzer and also play high-quality sound. The volume is controlled by a potentiometer. DFRobot FIT0449
zł31.78
24h
Available quantity: 73
Available
An audio module with a DAC converter and a stereo amplifier designed to work with the Raspberry Pi. Adafruit 3346
zł70.25
24h
Available quantity: 3
Available
Module with LM386 audio amplifier and loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 107020001
zł26.21
24h
Available quantity: 4
Available
Single-channel audio amplifier up to 100 W.
zł65.33
24h
Available quantity: 2
Available
A set with a vibration generator designed to transfer sounds through the human skeleton to the auditory center. DFRobot KIT0126
zł134.57
4 weeks
No product available!
Module with an AB class amplifier based on the Boomer® LM4853 system. It can work in two modes: mono (power 1.5 W, load 4 Ω) or stereo (power 300 mW, load 8 Ω). It has a potentiometer for power control and gain control for the left and right channel. SparkFun DEV-14475
zł95.58
24h
Available quantity: 2
Available
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
zł159.00
24h
Available quantity: 6
Available
Module containing TSH82 operational amplifier from STMicroelectronics. The system has two built-in amplifiers and each of them is available separately on the pins of the board as inverting amplifiers. Sparkfun BOB-14874
zł43.32
24h
Available quantity: 2
Available
LM386 audio amplifier module. It is supplied with the voltage ranging from 4 to 12 V. The set includes an 8 Ω, 0.5 W loudspeaker. DFRobot DFR0064
zł53.65
24h
Available quantity: 1
Available
Module with two operational amplifiers OPA627