Best sellers
There are 15608 products.
Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460
Module with an analog gas sensor. It allows you to measure the concentration of NO, NO2 and H2. DFRobot SEN0441
A set with a radio transmitter and receiver operating at 433 MHz. The modules are equipped with Gravity connectors and communicate via a digital interface. DFRobot TEL0140-1
Standard analog servo with plastic gear. It has a 180° range of motion and derived feedback output. Pololu 3442
Nylon PA12 filament in Natural with a diameter of 1.75 mm. 0.75 kg of filament is wound on a spool. Fiberlogy Nylon PA12 Natural
Universal organizer with containers. It allows you to store small parts and components. Kistenberg KNO35255B
Easy PLA filament in True Gold, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA True Gold
Adafruit 3527 is a small display, ready to connect on any Raspberry Pi computer. It is equipped with a 128x32 monochrome OLED display with sharp white pixels. OLED uses only I2C pins, so it offers many GPIO connections available for buttons, LEDs, sensors etc. It is also nice and compact. Adafruit 3527
The S9V11F3S5 switching step-up/step-down regulator efficiently produces a fixed 3.3 V (default) or 5 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)
Easy PLA filament in Beige, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Beige
The S9V11F5S6CMA switching step-up/step-down regulator efficiently produces a fixed 5 V (default) or 6 V (selectable) output whether it is higher or lower than the input voltage, which can range from 2 V to 16 V. (Note: minimum start-up voltage is 3 V, but it operates to 2 V after that.)
The S9V11MACMA switching step-up/step-down regulator efficiently produces a finely adjustable output between 2.5 V and 9 V whether it is higher or lower than the input voltage, which can range from 3 V to 16 V. The regulator also has a precision-adjustable low-voltage cutoff with hysteresis that can be used to prevent battery over-discharge.
Easy PLA filament in Burgundy, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Burgundy
Easy PLA filament in Light Green, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Light Green
Easy PLA filament in Navy Blue, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Navy Blue
Easy PLA filament in Pink, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Pink
The FS5106R is a standard-sized servo that has been built by FEETECH specifically for continuous rotation, making it an easy way to get your robot moving. It features two ball bearings on the output shaft for reduced friction, and it offers easy access to the rest-point adjustment potentiometer.
Easy PLA filament in Onyx, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Onyx
FiberFlex 40D filament in Purple with a diameter of 1.75 mm. 0.85 kg of filament is wound on a spool. Fiberlogy FiberFlex 30D Purple
Easy PLA filament in Aurora, 1.75 mm in diameter. 0.85 kg of filament is wound on a spool. Fiberlogy Easy PLA Aurora