

The socket tester is a device used for safe testing and diagnostics of electrical sockets and various parameters related to the voltage and operation of network circuits. It supports a wide operating voltage range from 90 to 250 V, which allows you to test sockets in various voltage standards. It also allows testing RCD (Residual Current Device) with a current greater than 30 mA. This allows you to verify the correct operation of the RCDs and check whether they react to the presence of incorrect current in the circuit. The tester is equipped with an LCD display with backlight, which makes it easy to read the results even in low light conditions. It meets the safety standards EN61010-1, -2-030 and EN61326-1 and has the CAT II 300V category, which proves its adequate protection for testing sockets in the voltage range up to 300 V.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Lanberg’s network cable tester is a multifunctional device for testing wires of ICT networks. z27375
This tester has been designed to easily and quickly check if a given cable is functional (by testing its pins). Lanberg NT-0403
Tester for testing cables with RJ45 and RJ11 plugs. Detects abnormalities such as short circuits, openings, reversed wires, swapped pairs. NAR0167
No product available!
Lan tester can easily read the correct pin configuration of 10Base-T cable, 10Base-2 cable, RJ45/RJ11 modular cables, 258A, TIA-568A/568B and Token Ring cable etc. by comparing one transmitting end to the corresponding receiving end. z28586
The tester allows you to test Ethernet, telephone and BNC cables. Performs basic conduction, short circuit, wire crossing and open circuit tests. Uni-T UT681C
No product available!
Universal set of tools for building a LAN network. Lanberg NT-0301
The socket tester allows you to check for sockets wiring errors. It helps to detect errors such as missing one of the wires or their incorrect connection. Uni-T UT07A-EU
No product available!
The NEO TOOLS 94-007 non-contact voltage tester enables quick and precise detection of alternating voltage and identification of faults in wires. With two measurement modes, light and sound signaling, and a compact design with a pocket clip, this tool is an essential piece of equipment for every electrician and field installer.
The non-contact voltage and phase tester is a practical measuring tool that allows quick and safe detection of voltage, phase and phase sequence in various electrical installations.
The non-contact voltage and phase tester is a practical measuring tool that allows quick and safe detection of voltage, phase and phase sequence in various electrical installations.
The cable locator detects Ethernet, telephone and power cables. It consists of a transmitter and a receiver. It is the recommended tool for detecting communication cables and A/V cables faults. Uni-T UT682
No product available!
The tester allows you to test Ethernet and telephone cables. Performs basic conduction, short circuit, wire crossing and open circuit tests. Uni-T UT681L
No product available!
The cable locator is used to detect telephone and power cables without opening their insulation. It consists of a transmitter and a receiver. It is the recommended tool for troubleshooting communication cables and A/V cables. Uni-T UT682D
Multifunctional device for scanning and testing wires in telecommunicational networks. Lanberg NT-0501
The Nano size test clip from Test Products International Inc offers an opening of 0.64 mm and is one of the best on the market, although it requires gentle handling. It may be necessary to spread the handles by hand to properly close the clamp.
The socket tester allows you to check the wiring errors of the sockets. It helps to detect errors such as missing one of the wires, incorrect connection and performing a Residual Current Device (RCD) test. Uni-T UT07B-EU
A network socket tester that allows you to check socket wiring errors. It helps to detect such problems as missing one of the wires or their incorrect connection.