zł10,639.61
.png)
New products
New products New products
Pololu CT433 TMR Current Sensor 0-65A 3.3V
ID: 1194452
5902186340428
zł63.92
Tax included
zł51.97 tax excl.
The module enables unidirectional AC and DC current measurement over a range from 0 A to 65 A. XtremeSense™ TMR technology, an electrically isolated current path, 1 MHz bandwidth, and an analogue voltage output support use in systems requiring fast current measurement and high dV/dt immunity. Pololu CT433-HSWF65DR Large Carrier 0–65 A, 3.3 V
Description
Device Pololu CT433-HSWF65DR Large Carrier uses the Allegro CT433-HSWF65DR sensor intended for unidirectional current measurement. The module requires a supply voltage from 3.0 V to 3.6 V, while the output voltage is 0.65 V at 0 A and increases by 30.8 mV for each ampere of current. The output is non-ratiometric, so the zero point and sensitivity remain independent of the actual supply voltage within the permitted range.
The six-layer PCB with 2 oz copper supports heat dissipation during high-current operation. Connection holes with a diameter of 6.6 mm and a spacing of 22 mm support M6 screws, ring terminals, or wires up to 4 AWG. During testing, the manufacturer achieved approximately 55 A continuous current at an ambient temperature of around 25°C without forced-air cooling. For average currents above 30 A, temperature monitoring and additional cooling should be considered.
Features
- Type: current sensor module
- Module manufacturer: Pololu
- Pololu product number: 5339
- Sensor IC: Allegro CT433-HSWF65DR
- Sensing technology: XtremeSense™ TMR
- Measurement direction: unidirectional
- Measured current type: AC and DC
- Measurement range: 0 A to 65 A
- Supply voltage: 3.0 V to 3.6 V
- Nominal supply voltage: 3.3 V
- Typical supply current: 6 mA
- Output interface: analogue
- Sensitivity: 30.8 mV/A
- Output voltage at 0 A: 0.65 V
- Non-ratiometric output
- Bandwidth: 1 MHz
- Typical response time: 300 ns
- Sensor primary current path resistance: 1 mΩ
- Electrically isolated current path
- Common-mode magnetic field rejection
- Suitable for high dV/dt applications
- Overcurrent fault output: FLT
- FLT activation threshold: approximately 110% of the maximum linear range
- FLT active only while the fault condition is present
- Number of PCB layers: 6
- Copper thickness: 2 oz
- Board dimensions: 30.5 × 35.6 mm
- Weight: 4.3 g
- Current-path connection hole diameter: 6.6 mm
- Connection hole spacing: 22 mm
- Supported screws: M6 or 1/4"
- Maximum directly soldered wire size: 4 AWG
- Signal pins: FLT, VOUT, VCC, GND
- Signal pin pitch: 2.54 mm
- Recommended measured-circuit voltage: below 30 V
- Operating temperature range: −40°C to 125°C
1194452
Data sheet
- Interface
- Sygnał analogowy
- Zakres pomiarowy
- 0 - 65 A
- Sposób podłączenia
- Szeregowy
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Other products in the same category (16)
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5260
zł56.41
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5262
zł58.38
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5263
zł56.41
24h
Available quantity: 2
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5270
zł68.47
24h
Available quantity: 3
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5271
zł68.49
24h
Available quantity: 5
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5272
zł68.49
24h
Available quantity: 5
Available
The ACS72981 current sensor module uses the Hall effect to accurately and safely measure AC and DC current, providing electrical isolation of the current path. With a wideband analog output (up to 250 kHz) and low conduction resistance (0.2 mΩ), it minimizes energy loss and offers a fast response time of less than 2 µs. Pololu 5273
zł68.49
24h
Available quantity: 5
Available
Large Carrier version current sensor from Pololu, model 5274, based on the ACS72981LLRATR-100B5 IC, designed for measuring current in the range from -100 A to +100 A at a 5 V supply in applications requiring galvanic isolation and analog output. Pololu 5274
zł63.92
24h
Available quantity: 3
Available
Large Carrier version current sensor from Pololu, model 5275, based on the ACS72981LLRATR-100U3 IC, designed for measuring current in the range from 0 A to 100 A at a 3.3 V supply in applications requiring galvanic isolation and analog output. Pololu 5275
zł63.92
24h
Available quantity: 3
Available
Large Carrier version current sensor from Pololu, model 5276, based on the ACS72981LLRATR-100U5 IC, designed for measuring current in the range from 0 A to 100 A at a 5 V supply in applications requiring galvanic isolation and analog output. Pololu 5276
zł63.92
24h
Available quantity: 3
Available
Large Carrier version current sensor from Pololu, model 5277, based on the ACS72981KLRATR-150B3 IC, designed for measuring current in the range from -150 A to +150 A at a 3.3 V supply in applications requiring galvanic isolation and analog output. Pololu 5277
zł63.92
24h
Available quantity: 2
Available
Pololu 5278 Large Carrier current sensor based on the ACS72981KLRATR-150B5 chip, designed for bidirectional current measurement from -150 A to +150 A with 5 V supply voltage in applications requiring galvanic isolation and an analog output signal. Pololu 5278
zł63.92
24h
Available quantity: 2
Available
Current sensor in the Large Carrier version based on the ACS72981KLRATR-150U3 chip, designed for unidirectional current measurement from 0 A to 150 A with a 3.3 V supply voltage. The module uses Hall-effect sensing, an electrically isolated current path, and an analog output with a sensitivity of 17.6 mV/A proportional to the measured current. Pololu 5279
zł63.92
24h
Available quantity: 5
Available
Current sensor in the Large Carrier version based on the ACS72981KLRATR-150U5 chip, designed for unidirectional current measurement from 0 A to 150 A with a 5 V supply voltage. The module uses Hall-effect sensing, an electrically isolated current path, and an analog output with a sensitivity of 26.7 mV/A proportional to the measured current. Pololu 5280
zł63.92
24h
Available quantity: 5
Available
Current sensor in the Large Carrier version based on the ACS72981ELRATR-200B5 chip, designed for bidirectional current measurement from -200 A to +200 A with a 5 V supply voltage. The module uses Hall-effect sensing, an electrically isolated current path, and an analog output signal proportional to the measured current. Pololu 5282
zł63.92
24h
Available quantity: 5
Available
Current sensor in the Large Carrier version based on the ACS72981ELRATR-200U3 chip, designed for unidirectional current measurement from 0 A to 200 A with a 3.3 V supply voltage. The module uses Hall-effect sensing, an electrically isolated current path, and an analog output signal proportional to the measured current. Pololu 5283
zł63.92
24h
Available quantity: 5
Available
The module enables unidirectional AC and DC current measurement over a range from 0 A to 65 A. XtremeSense™ TMR technology, an electrically isolated current path, 1 MHz bandwidth, and an analogue voltage output support use in systems requiring fast current measurement and high dV/dt immunity. Pololu CT433-HSWF65DR Large Carrier 0–65 A, 3.3 V