![Sharp GP2Y0A60SZLF analogowy czujnik odległości 10-150cm, 5V Sharp GP2Y0A60SZLF analogowy czujnik odległości 10-150cm, 5V](https://kamami.pl/25733-large_default/pololu-2474-pololu-carrier-with-sharp-gp2y0a60szlf-analog-distance-sensor-10-150cm-5v.jpg)
![Sharp GP2Y0A60SZLF analogowy czujnik odległości 10-150cm, 5V Sharp GP2Y0A60SZLF analogowy czujnik odległości 10-150cm, 5V](https://kamami.pl/25733-large_default/pololu-2474-pololu-carrier-with-sharp-gp2y0a60szlf-analog-distance-sensor-10-150cm-5v.jpg)
zł135.66 tax excl.
The GP2Y0A60SZ distance sensor from Sharp offers a wide detection range of 4″ to 60″ (10 cm to 150 cm) and a high update rate of 60 Hz. The distance is indicated by an analog voltage, so only a single analog input is required to interface with the module.
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Sharp’s distance sensors are a popular choice for many projects that require accurate distance measurements. This particular sensor is small and affordable, making it an attractive alternative to sonar rangefinders, while its wide sensing range and resistance to interference from ambient IR set it apart from other IR distance sensors. It consists of a Sharp GP2Y0A60SZLF module installed on our compact carrier board, which includes all of the external components required to make it work and provides a 0.1″ pin spacing that is compatible with standard connectors, solderless breadboards, and perfboards. With an ability to measure distances from as close as four inches to as far as five feet (10 cm to 150 cm), this sensor has the widest range of any of our Sharp distance sensors, and its 60 Hz update rate is more than twice that of Sharp’s older GP2Y0A02YK0F analog distance sensor that has a similar sensing range.
Interfacing to most microcontrollers is straightforward: the single analog output, OUT, can be connected to an analog-to-digital converter for taking distance measurements, or the output can be connected to a comparator for threshold detection. The sensor automatically updates the output approximately every 16 ms. The enable pin, EN, can be driven low to disable the IR emitter and put the sensor into a low-current stand-by mode. This pin is pulled high on the carrier board through a 10 kΩ pull-up resistor to enable the sensor by default.
A 1×4 strip of 0.1″ header pins and a 1×4 strip of 0.1″ right-angle header pins are included, as shown in the picture below. You can solder the header strip of your choice to the board for use with custom cables or solderless breadboards, or you can solder wires directly to the board itself for more compact installations. The board features one 0.125″ mounting hole that works with #4 or M3 screws (not included); if you do not need the mounting hole, you can cut that part of the board off to reduce its size.
The GP2Y0A60SZ supports two operating modes: 5V and 3V. In 5V mode, the recommended operating voltage is 2.7 V to 5.5 V, and the output voltage differential over the full distance range is approximately 3 V, varying from around 3.6 V at 10 cm to 0.6 V at 150 cm. In 3V mode, the recommended operating voltage is 2.7 V to 3.6 V, and the output voltage differential over the full distance range is approximately 1.6 V, varying from around 1.9 V at 10 cm to 0.3 V at 150 cm. The GP2Y0A60SZ datasheet (701k pdf) contains a plot of analog output voltage as a function of the distance for the two modes.
Our GP2Y0A60 carrier board is available configured for 5V mode or configured for 3V mode.
The only difference between the two versions is the presence or absence of a zero ohm resistor as shown in the picture above (the component location is marked by a rectangle on the silkscreen). You can convert a 5V version to 3V by removing the resistor, and you can convert a 3V version to 5V by shorting across the two pads.
Note that the 5V version can be powered all the way down to 2.7 V, and the relationship between the sensor output voltage and distance is mostly independent of the supply voltage. The main drawback to powering the 5V version at a lower voltage is the output voltage will not exceed the supply voltage, so the effective minimum detection distance might increase (i.e. for distances that would result in output voltages above your supply voltage, the output will instead be capped at the supply voltage). On the other hand, if you mostly care about measuring distances closer to the maximum end of the range, you could benefit from the increased output voltage differential of the 5V version even if you are only powering it at 3.3 V.
Size: | 1.3″ × 0.41″ × 0.4″1 |
---|---|
Weight: | 2.5 g2 |
Maximum range: | 150 cm |
---|---|
Minimum range: | 10 cm |
Sampling rate: | 60 Hz3 |
Minimum operating voltage: | 2.7 V |
Maximum operating voltage: | 5.5 V |
Supply current: | 33 mA4 |
Output type: | analog voltage |
Output voltage differential: | 3 V |
Data sheet
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
No product available!
A-Star 32U4 Prime SV - a programmable Arduino board, based on the Atmel ATmega32U4 microcontroller from the AVR family. Version with soldered connectors, without micro-SD card slot, without display. Polol 3113
No product available!
The GP2Y0A60SZ offers a wide detection range of 4″ to 60″ (10cm to 150cm) and a high update rate of 60Hz. The distance is indicated by analog voltage - only a single analog input is required to interface with the module. Pololu 2476
VL53L8CX sensor module that offers fast and accurate distance measurement up to 4 m via I²C or SPI digital interface. It can measure distances to multiple targets simultaneously, providing depth map data with a resolution of up to 8x8. The built-in power supply circuit allows operation in the voltage range from 3.2 V to 5.5 V. Pololu 3419
Distance Measuring Sensor Unit Measuring distance: 4 to 30 cm Analog output type, voltage 4.5V-5.5 V, Sharp, RoHS
No product available!
Ultrasonic distance sensor (sonar) with a measuring range from 15 to 318 cm with the possibility of detecting objects in a selected zone. It allows you to read data via the USB interface. DFRobot SEN0279
No product available!
Maxbotix XL-MaxSonar-AE0 Sonar Range Finder MB1300
ToF VL53L0X distance sensor module designed for M5Stack sets. It allows you to measure distances up to 2 m and communicates via the I2C interface. M5Stack U072
Laser distance sensor with a measuring range of up to 4 m, based on the ToF measurement technique. Communication with the module takes place via the I2C interface. Waveshare VL53L1X Distance Sensor
Laser distance sensor with a measuring range of up to 4 m based on the ToF measurement technique. Communication with the module takes place via the I2C interface. Pimoroni PIM373
Expansion board equipped with VL6180 distance sensor, based on FlightSense technology. The set is designed to measure distances and detect gestures. X-NUCLEO-6180A1
Laser distance sensor with a measuring range of up to 2 m, based on the ToF measurement technique. Communication with the module takes place via the I2C interface. Waveshare VL53L0X Distance Sensor
Module with ToF VL53L5CX sensor with a matrix of 64 pixels and a range of up to 4 m. It is equipped with a Qwiic connector and communicates via the I2C interface. SparkFun SEN-18642
Parallax PING))) Ultrasonic Sensor #28015
No product available!
Recognizes the distance of an object away from the sensor up to about 10 inches (~25cm) and the location of the object from side to side across the sensor in about a 6 inch (~15cm) span. You will be able to use I2C or UART to communicate with the ZX Sensor via an Arduino-based microcontroller as well as a computer. SEN-12780
ToF distance sensor (Time of flight) with a range of up to 5 m. The module is supplied with the voltage of 3.3 V and communicates via the I2C interface. SparkFun SEN-19218
Optical distance sensor in the range of 10-80 cm with an analogue output, power supply 4.5-5.5V.
TF Mini LiDAR is a one-way rangefinder that is based on ToF (Time of Flight) technology. It consists of high quality optical and electrical devices that provide stability, high sensitivity and precision. Sparkfun SEN-14786
No product available!
Laser distance sensor with a measuring range of up to 2 m, based on the ToF measurement technique. Communication via the I2C interface
The GP2Y0A60SZ distance sensor from Sharp offers a wide detection range of 4″ to 60″ (10 cm to 150 cm) and a high update rate of 60 Hz. The distance is indicated by an analog voltage, so only a single analog input is required to interface with the module.