![Gravity: Analog Signal Isolator - analog signal isolator Gravity: Analog Signal Isolator - analog signal isolator](https://kamami.pl/30203-large_default/gravity-analog-signal-isolator-analog-signal-isolator.jpg)
![Gravity: Analog Signal Isolator - analog signal isolator Gravity: Analog Signal Isolator - analog signal isolator](https://kamami.pl/30203-large_default/gravity-analog-signal-isolator-analog-signal-isolator.jpg)
zł77.28 tax excl.
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
Gravity: Analog Signal Isolator is a module that prevents electrical interference between sensors. In many cases, to ensure reliable operation of the sensors, isolation of the sensors in the device is required, because they can interfere with each other and will not perform correct measurements. The insulating module allows to separate the sensors in the device and increase the stability and reliability of operation. The module has a built-in 5V power supply, so you do not need to connect an external, additional power source for the sensor. The module has been equipped with a Gravity connector allowing easy connection of sensors to the module. The tile can be used, for example, in a multi-parameter water quality monitoring system.
In order for the module to work properly, it should be noted that:
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
A module with a 3-channel ADC ADC ADS1015, which allows you to read voltages from -24 V to +24 V with a sampling frequency of up to 3.3 kHz and a resolution of 12 bits. Pimoroni PIM422
Gravity module designed based on the GP8512 system. It is a single-channel DAC (analog-to-digital) converter with I2C communication that offers an output signal with a resolution of 15-bit and an accuracy of 0.01%. It allows you to generate analog signals with a voltage range from 0 to 2.5 V or from 0 to VCC. DFRobot DFR1035
The power module is designed for the MyoWare 2.0 muscle tension sensor. Equipped with a LiPo battery, it allows you to build portable devices. SparkFun DEV-18427
The Class D digital audio amplifier module has two channels with a power of 30 W and can work with speakers from 4 to 8 Ω. Powered with the voltage ranging from 8 to 26 V. Bluetooth communication
Class D stereo digital audio amplifier module PAM8403. The system allows you to connect two speakers with an impedance from 4 to 8 Ω and a power of 3 W
Module with a precise clock RTC DS3231 dedicated to the Raspberry Pi Pico. Communication via the I2C interface. SB Components 21420
No product available!
Small size driver module TB67S279FTG stepper motor powered with 10 ... 47V voltage and working current 1.1A. The controller allows you to control the motor movement up to 7 different resolutions (up to 1/32 of a step). Module with soldered connectors. Polol 3099
Module with Flash memory W25Q64 with a capacity of 64 Mbit (8 MB). It communicates via the QSPI interface. Adafruit 5633
No product available!
Clock signal generator with a frequency of 8 kHz to 160 MHz based on the SI5351A integrated circuit. Communication with the module takes place via the I2C bus. Adafruit 5640
MicroSD card reader module, shield type for Wemos D1
No product available!
Lens with CS-mount and 3.2 mm focal length with a very wide angle of view of 120°. Designed to work with the Raspberry Pi HQ camera. ArduCAM LN051
No product available!
Module with a bistable button and green LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-G
MP6550 DC motor controller module. It can work with motors supplied with voltage from 1.8 to 22 V and current consumption up to 1.7 A. Pololu 4733
Gravity: Analog Signal Isolator is a module that allows to isolate sensors in the system and eliminate mutual interference of sensors powered by 5V. DFRobot DFR0504