Grove Thermal Imaging Camera - module with MLX90640 (FoV 110°)
ID: 583091
zł786.54
Tax included
zł639.46 tax excl.
Module with a MLX90640 thermal imaging camera with a 32x24 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 114020142
Description
Module with a MLX90640 thermal imaging camera with a 32x24 field matrix and a 110° viewing angle. It enables temperature measurement in the range from -40°C to 300°C with high accuracy down to 1°C. The infrared thermal imager is equipped with a sensitive heat sensor that can detect slight differences in the temperature of objects in the environment. It then collects this radiation information from the objects and creates an electronic image based on the temperature difference information. The board is equipped with a Grove connector, so it can be used with the Base Shield V2. The module communicates via the I2C interface and is supplied with the voltage from 3 V to 6 V. Full documentation of the module with examples of use is available on the product page.
Attention!
To operate the module, a chip with at least 20 KB of RAM is required.Features
- Sensor: MLX90640
- Resolution: 32x24
- FoV: 110° x 75 °
- Temperature measurement range: -40 ? to 300 ?
- Refresh rate: 0.5Hz to 64Hz
- I2C interface
- I2C adress: 0x33
- Supply voltage: 3 V to 6 V
- Current consumption: 18 mA
583091
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A small module, matching the breadboard, containing a 32-bit microcontroller with ARM Cortex M7 core. PJRC TEENSY40
zł124.07
24h
Available quantity: 17
Available
Module with a MLX90641 thermal imaging camera with a 16x12 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020892
zł547.69
24h
Available quantity: 1
Available
Other products in the same category (16)
A small servo (23 x 11.5 x 24 mm) with a weight of 8.6 g, power supply 4.8-6V, maximum torque 1.8 kg / cm (at 6V). It has a connector compatible with the Grove standard. Seeed Studio 316010005
zł36.11
24h
Available quantity: 2
Available
MH-Z16 carbon dioxide sensor with Grove connector. It communicates via the UART interface. Seeed Studio 101020067
zł563.83
24h
Available quantity: 1
Available
Speech recognition module with Nuvoton ISD9160 system, microphone, Flash memory and speaker output. The board is equipped with a Grove connector and communicates via the UART interface. Seeed Studio 101020232
zł104.60
24h
Available quantity: 2
Available
Recorder v3.0 is a module that allows you to record and play sounds. The module was based on the ISD9160FI system, it also has a FLASH memory with a capacity of 2 MB, which allows for recording up to 83 seconds long. The set contains a small loudspeaker on which recorded sounds can be played. Seeed studio 107020029
zł60.82
24h
Available quantity: 1
Available
Module with a reflection sensor (line sensor) RS-06WD. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 101020172
zł22.18
24h
Available quantity: 2
Available
The module allows the detection of volatile organic compounds (VOC) in the air, based on Winsen\'s WSP2110 system. Allows for detection in the air; formaldehyde (HCHO), methane, benzene, toluene, alcohol, etc. The sensor output is an analog signal. Seeed studio 101020001
zł79.32
24h
Available quantity: 4
Available
Module with LoRa transmitter based on RFM95 (SX1276 LoRa®). It works with a frequency of 433 MHz, maximum power up to 100 mW and a power gain of up to + 20dBm. The module has a built-in antenna, but it is possible to connect an external antenna (MHF connector). The module has a connector in accordance with the Grove standard. Seeed studio 113060007
zł84.92
24h
Available quantity: 1
Available
Module with a pulse sensor (heart rate). The board is equipped with a Grove connector and a digital output in the form of pulses. Seeed Studio 101020033
zł72.41
4 weeks
No product available!
Base Shield V2 is an extension for tiles with an Arduino shield connector, it has a Grove connector, which can be connected to Grove-compatible modules / sensors. Seeedstudio 103030000
zł24.40
24h
Available quantity: 14
Available
3-port I2C splitter module. The board is equipped with Grove connectors and allows you to connect additional I2C devices. Seeed Studio 103020006
zł15.72
24h
Available quantity: 4
Available
Module with a voltage divider. Equipped with a Grove connector, it allows the input voltage to be reduced by 3 or 10 times. Seeed Studio 104020000
zł28.20
4 weeks
No product available!
Base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug the NodeMCU into the slot and use the Grove sensor ports. Seeed Studio 105020008
zł57.18
24h
Available quantity: 4
Available
Universal module for prototyping. It has 58 prototype fields and a Grove connector. Seeed Studio 101020035
zł11.32
4 weeks
No product available!
Grove adapter for 3.5mm screw connector. Seeed Studio 103020007
zł8.12
24h
Available quantity: 3
Available
Set (5 pieces) of wires for attaching modeling servos with the Grove system. With one wire you can connect 2 servos to one Grove slot. Seeed studio 110990057
zł30.73
24h
Available quantity: 1
Available
GrovePi + is an extension in the form of a HAT overlay intended for Raspberry Pi computers (B / B + / A + / 2/3/3 +). The module has 15 connectors to which modules / sensors compatible with the Grove standard can be connected. Seeed Studio 103010002
zł298.47
24h
Available quantity: 3
Available
Module with a MLX90640 thermal imaging camera with a 32x24 field matrix and a 110° viewing angle. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 114020142