zł10,639.61
.png)
New products
New products New products
Grove Base Shield - base plate for NodeMCU
ID: 566573
5906623414383
zł57.18
Tax included
zł46.49 tax excl.
Base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug the NodeMCU into the slot and use the Grove sensor ports. Seeed Studio 105020008
Description
Grove Base Shield is a base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug NodeMCU into the socket and conveniently use the ports led out to special connectors for Grove sensors.
Specification
- Compatible with all Grove modules
- 5 digital connectors (D3-D8)
- 1 analog connectors (A0)
- 2 I2C sockets
- UART connector (D9-D10)
- Power LED indicator
- Dimensions: 134 x 64 x 32 mm
- Weight: 40 g
566573
Manufacturer
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
Responsible person
- BTC Korporacja sp. z o. o.
- Ludwinowo Zegrzyńskie 52G
- 05-140 Ludwinowo Zegrzyńskie
- Poland
- [email protected]
- 22 767 36 20
You might also like
WiFi module based on ESP8266. The module has a built-in antenna and USB-UART converter. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. 10 GPIO lines are available which each can be configured to work as PWM, I2C.
zł19.48
24h
Available quantity: 25
Available
The base board for the Wi-Fi NodeMCU module (ESP-12E), thanks to the built-in L293DD system, allows for attaching e.g. motors, electromagnets or other executive devices. The I/O lines of the NodeMCU module were derived to the pin connectors, and the power supply can be connected with the use of screw connectors. ESP12E Motor Shield
zł7.07
24h
Available quantity: 8
Available
LoLin NodeMCU V3 is a board with ESP8266 (ESP12E). The ESP8266 system provides WiFi connectivity (802.11 b / g / n). The USB-UART converter (CH340G chip) is located on the board. The module can be programmed in Lua (under the control of the NodeMCU firmware) or in the Arduino environment. There are 10 GPIO lines available.
zł14.90
24h
Available quantity: 13
Available
Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini
zł18.24
24h
Available quantity: 29
Available
Other products in the same category (16)
The module with the tilt sensor, the sensor output is a digital signal. The module has a connector in accordance with the Grove standard. Seeed studio 101020025
zł17.37
24h
Available quantity: 2
Available
The touch sensor module (touch button) can be used as a replacement for traditional mechanical buttons. It operates based on the TTP223-B system, which measures the capacity of the metal field on the module. The module has a connector in accordance with the Grove standard. Seeed studio 101020037
zł21.35
24h
Available quantity: 2
Available
Module with a magnetic sensor based on the CT10 reed switch. CT10 is a unipolar reed switch, normally open. The sensor reacts to the action of an electromagnet, permanent magnet or a combination thereof. The module has a connector in accordance with the Grove standard. Seeedstudio 101020038
zł19.83
4 weeks
No product available!
The Hall sensor module allows magnetic field detection, can be used to measure angle of rotation, displacement, mechanical vibrations, etc. The module has a connector in accordance with the Grove standard. Seeed studio 101020046
zł18.33
24h
Available quantity: 2
Available
Module with a flame sensor or other light sources with a wavelength in the range of 760 to 1100 nm. It was based on the YG1006 sensor (photovolver NPN). The sensor has a connector compatible with the Grove standard. Seeed studio 101020049
zł38.14
24h
Available quantity: 2
Available
The kit includes a control module (with ETA1617 and NE555) and an ultrasonic transducer. The water atomiser module allows for the construction of, for example, a small humidifier. The module has a connector in accordance with the Grove standard. Seeed studio 101020090
zł40.76
24h
Available quantity: 3
Available
Module with RGB LED, it is possible to control individual colors using digital signals as well as PWM signals. The module has a connector in accordance with the Grove standard. Seeed studio 101020472
zł21.19
24h
Available quantity: 3
Available
Module with red LED diode and potentiometer. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 104030005
zł10.90
24h
Available quantity: 3
Available
Grove module with a small vibration motor. Seeed studio 105020003
zł16.49
4 weeks
No product available!
Module with an active buzzer. The board is equipped with a Grove connector and is controlled by a digital signal. Seeed Studio 107020000
zł8.36
24h
Available quantity: 3
Available
Module with LM386 audio amplifier and loudspeaker. The board is equipped with a Grove connector and is controlled by a PWM signal. Seeed Studio 107020001
zł26.21
24h
Available quantity: 4
Available
Module with a 3-axis MMA7660FC accelerometer with a measuring range up to ± 1.5g. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020039
zł64.13
24h
Available quantity: 2
Available
Module with a gesture sensor PAJ7620U2, which allows to recognize up to 13 gestures. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020083
zł60.29
4 weeks
No product available!
Module with OLED 0.96" display with a resolution of 128x64 px. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 104030008
zł94.59
24h
Available quantity: 2
Available
Module with pressure and temperature sensor BMP280. The board is equipped with a Grove connector and communicates via the I2C or SPI interface. Seeed Studio 101020192
zł60.63
24h
Available quantity: 2
Available
Module with humidity and air temperature sensor based on the AM2302 system. It allows temperature measurement in the range from -40 to 80 ° C and the humidity measurement takes place in the range of 5 to 99% RH. The module has a connector in accordance with the Grove standard. Seeed Studio 101020019
zł62.32
24h
Available quantity: 5
Available
Base plate designed for NodeMCU (ESP8266 WIFI). The module is an expansion board that allows you to plug the NodeMCU into the slot and use the Grove sensor ports. Seeed Studio 105020008