

FRAM, or Ferroelectric Ram, is the coolest new data storage method that all the fashion magazines are talking about. Oh wait, no that's quilted handbags. But FRAM is pretty damn cool too! It's similar to Dynamic random-access memory, only with a ferroelectric layer instead of a dielectric layer. This gives it stable handling (the bytes you write are non-volatile) with dynamic responsiveness (you can write them very fast!).
Now, with our I2C FRAM breakout board you can add some FRAM storage to your next DIY project. FRAM allows for a lower power usage and a faster write performance. It's excellent for low-power or inconsistent-power datalogging or data buffering where you want to stream data fast while also keeping the data when there's no power. Unlike Flash or EEPROM there's no pages to worry about. Each byte can be read/written 10,000,000,000,000 times so you don't have to worry too much about wear leveling.
This particular FRAM chip has 256 Kbits (32 KBytes) of storage, interfaces using I2C, and can run at up to 1MHz I2C rates. Each byte can be read and written instantaneously (like SRAM) but will keep the memory for 95 years at room temperature.
We picked up the largest chip that has I2C and is also 5V compliant. You can use this chip with either 3V or 5V power and logic. It comes in a breadboard-friendly breakout and a spare stick of 0.1" male header for soldering on.
We also have an SPI FRAM breakout board - which is smaller in size but faster (20MHz max SPI clock rate).
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with EEPROM memory, capacity 512 kbit (64kB). Communication takes place via the I2C interface. The module has 3 jumpers that enable selection of one of 8 addresses. SparkFun SPX-14764
W25Q128JV flash memory module with 128 Mbit (16 MB) capacity. It supports communication via SPI, Dual or Quad SPI interface. Waveshare W25QXX DataFlash Board
Module with EEPROM 24LC32 memory with a capacity of 32 kBit (4 kB). Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 5146
Module with Flash memory W25Q16 with a capacity of 16 Mbit (2 MB). It communicates via the QSPI interface. Adafruit 5632
FRAM memory module with MB85RC256V chip with a capacity of 32 kB. It is supplied with the voltage from 2.7 to 5.5 V and communicates via the I2C interface
No product available!
A small module with Flash memory W25Q65 with a capacity of 64 Mbit (8 MB). It communicates via the SPI interface
The module with the EEPROM 24LC256 memory chip with a capacity of 32 kB. It is supplied with the voltage ranging from 2.5 V to 5.5 V and communicates via the I2C interface (Gravity connector). DFRobot DFR0117
Module with 512 kbit (64kB) EEPROM. Communication is via the I2C interface. The module has 3 jumpers to select one of 8 addresses. SparkFun COM-18355
Module with Flash memory W25Q64 with a capacity of 64 Mbit (8 MB). It communicates via the QSPI interface. Adafruit 5633
No product available!
2 Kbit (256 B) EEPROM module with AT24C02 chip in SMD version. It communicates via the I2C interface
The KAmod SPI Flash module with W25Q128 memory provides a functional storage expansion for projects requiring larger data retention, such as measurement logging, system configurations, or event logs. Its compact form factor and standard pin layout make it easy to use in both prototyping and production applications that utilize the SPI bus.
Module with EEPROM memory with a capacity of 256 Kbit (32 kB) with the AT24C256 chip in the DIP version. It communicates via the I2C interface
A module with EEPROM memory with a capacity of 256Kbit (32kB) with the AT24C256 chip in the SMD version. It communicates via the I2C interface
The KAmod SPI Flash module with the W25Q80 chip is a compact solution for memory expansion in embedded projects, data logging systems, configuration buffers, and applications requiring independent storage space. Its standard pin pitch allows easy use in prototyping and quick connection to popular microcontrollers supporting the SPI interface.
The EEPROM memory module with the built-in AT24C32D chip allows storing data without loss after switching off the power supply. MOD 50
Module with Flash memory W25Q16 with a capacity of 16 Mbit (2 MB). It communicates via the SPI interface. Adafruit 5635
I2C FRAM breakout board you can add some FRAM storage to your next DIY project. FRAM allows for a lower power usage and a faster write performance. Adafruit 1895