

zł100.20 tax excl.
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 4.995:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. Pololu 3060
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 4.995:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.
Key specs at 6 V: 6000 RPM and 120 mA with no load, 2 oz-in (0.1 kg-cm) and 1.6 A at stall.
These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.
The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).
Versions of these gearmotors are also available with an additional 1 mm-diameter output shaft that protrudes from the rear of the motor. This 4.5 mm-long rear shaft rotates at the same speed as the input to the gearbox and offers a way to add an encoder, such as our magnetic encoder for micro metal gearmotors, to provide motor speed or position feedback.
With the exception of the 1000:1 gear ratio versions, all of the micro metal gearmotors have the same physical dimensions, so one version can be easily swapped for another if your design requirements change.
Note!
Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 35 oz-in (2.5 kg-cm) for the 1000:1 gearboxes and 25 oz-in (2 kg*cm) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.Dimensions
General specifications
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pololu high power miniature motor with carbon brushes. 50:1 gear motor, shaft speed 420 rpm, torque 0,54kg*cm. The motor has an extended shaft, which makes it easy to attach the encoder. Pololu 2379
Pololu high power miniature motor with carbon brushes. 150:1 gear motor, shaft speed 150 rpm, torque 1,3kg*cm. The motor has an extended shaft, which makes it easy to attach the encoder. Pololu 2382
No product available!
Small metal gear motor, 500 RPM speed, 12V operating voltage. GA12-N20-0026
No product available!
Miniature, 6V brush DC motor with metal gear with 15,25:1 gear ratio. It has a cross section of 10 × 12 mm, and the D-shaped output shaft has a length of 10 mm and a diameter of 3 mm. Pololu 4787
Small metal gear motor, 100 RPM speed, 6V operating voltage. GA12-N20-0014
No product available!
Small metal gear motor, 200 RPM speed, 12V operating voltage. GA12-N20-0024
No product available!
A small motor with a metal gear ending with a shaft with M3 thread, rotation speed 50 RPM, operating voltage 6 V. GA1036-N20M-0053
DC Micro motor module with metal gear with a gear ratio of 50:1. The motor is connected to the board containing the driver. DFRobot DFR0429
A small, high-power motor with a 30:1 metal gear, 12 V operating voltage, 0.06 A to 0.75 A power consumption, 1100 RPM speed, maximum torque of 0.39 kg*cm and carbon brushes with increased durability. Pololu 3038
No product available!
Small motor with metal gear and encoder, rotation speed 1000 RPM, operating voltage 6 V. GA46-N20E-0050
No product available!
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 100.37:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. This version also has a 4.5 × 1 mm extended motor shaft.
No product available!
A small, high power motor with a 50: 1 metal gear, 12 V operating voltage, 0.06 A to 0.75 A power consumption, 650 RPM speed, maximum torque of 0.67 kg * cm and carbon brushes with increased durability. Pololu 3039
No product available!
Miniature high-power motor from the Pololu MP series. Gear motor 5: 1,
the rotational speed of the shaft is 4400 rpm, the torque is 0.1 kg * cm (0.01 Nm).
The motor has an extended shaft which makes it easy to attach the encoder. Pololu 2376
No product available!
Small metal gear motor, 200 RPM speed, 6V operating voltage. GA12-N20-0015
No product available!
No product available!
Small, high power motor with 298:1 metal gear, 12 V operating voltage, 0.06 A to 0.75 A power consumption, 110 RPM, maximum torque 3.3 kg*cm and carbon brushes for extra durability. Pololu 3045
No product available!
This gearmotor is a miniature high-power, 6 V brushed DC motor with long-life carbon brushes and a 4.995:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. Pololu 3060