50:1 Micro Metal Gearmotor MP 6V
search
  • 50:1 Micro Metal Gearmotor MP 6V
ID: 198458
zł113.25
Tax included

zł92.07 tax excl.

Miniature medium-power, 6 V brushed DC motor with a 51.45:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. Pololu 2365

4 weeks
On request
Kamami is the official distributor of electronic modules and Pololu robotic parts. All products of this brand in our offer are original and come directly from the manufacturer.

Description

This gearmotor is a miniature medium-power, 6 V brushed DC motor with a 51.45:1 metal gearbox. It has a cross section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter.

Key specs at 6 V: 420 RPM and 40 mA with no load, 12 oz-in (0.9 kg-cm) and 0.7 A at stall.

These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-power 6 V and 12 V motors with long-life carbon brushes (HPCB), and high-power (HP), medium power (MP), and low power (LP) 6 V motors with shorter-life precious metal brushes. The 6 V and 12 V HPCB motors offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6 V HPCB and 6 V HP motors are identical except for their brushes, which only affect the lifetime of the motor.

The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other micro metal gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).

Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 35 oz-in (2.5 kg-cm) for the 1000:1 gearboxes and 25 oz-in (2 kg*cm) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.

Features

  • Gear ratio: 51.45:1
  • Free-run speed @ 6V: 420 rpm
  • Free-run current @ 6V: 40 mA
  • Stall current @ 6V: 700 mA
  • Stall torque @ 6V: 12 oz·in
  • Extended motor shaft?: N
  • Motor type: 0.7A stall @ 6V (MP 6V)
  • Size: 10 × 12 × 26 mm (output shaft adds 9 mm to the 26 mm length)
  • Weight: 9.5 g
  • Shaft diameter: 3 mm, D shaft

198458

Data sheet

DC motor power
MP
Gear material
Metal
Gear ratio
50:1
Rotation speed
420RPM
Shaft diameter
3 mm
Shaft shape
D
Obustronny wał silnika
Nie
Power supply voltage
6V

Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20

Other products in the same category (16)