Qwiic Dual Solid State Relay - 2-channel module with 25A relays
ID: 581681
zł901.07
Tax included
zł732.58 tax excl.
Module with 2 relays controlled by the I2C interface. Each relay can switch currents up to 25 A at 12 to 280 V AC. SparkFun COM-16810
Description
Module with 2 relays controlled by the I2C interface. It is based on the ATTiny84 microcontroller, which is pre-programmed. The I2C address of ATTiny84 is software configurable. Each relay can switch currents up to 25 A at 12-280 V AC. The module is equipped with a Qwiic connector. A guide and Arduino libraries are available for the module.
Features
- Power supply: 2.5 to 3.6 V (3.3 V recommended)
- I2C address: 0x0A (default), 0x0B
- Relay SSRF240D25:
- Maximum current: 25 A.
- Output voltage: 12 - 280 VAC
- Low EMI/EFI
- Low inrush current 15 mA
- 2.5 kV insulation
- Zero Cross Trigger
- Normally open circuit
- 2 x Qwiic connector
581681
Data sheet
- Output current
- 25 A
- Number of channels
- 2
- Executive element
- SSR
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
No product available!
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
zł11.94
24h
Available quantity: 9
Available
Flexible 4-core cable, 100 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17259
zł12.50
24h
Available quantity: 39
Available
Flexible 4-core cable, 200 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17258
zł12.90
24h
Available quantity: 10
Available
Other products in the same category (16)
Available
ModRL01 module with 10A/250VAC (10A/24VDC) relay, supply of 5 V load relay coil, additional control circuit, protected overvoltage control
zł5.57
24h
Available quantity: 23
Available
The remotely controlled modulation module MOD-34 / AZ allows wireless load control with up to 10 A current consumption via a relay. It does not contain nRF24l01.
zł51.94
24h
Available quantity: 1
Available
The module contains two 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL02_ISO
zł8.54
4 weeks
No product available!
The module contains four 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select switching with high or low status. The module is equipped with screw connectors. modRL04_ISO
zł22.40
4 weeks
No product available!
The module contains eight 5V relays with a maximum current of 10A (250 VAC) and opto-isolated inputs, and with jumpers it is possible to select high or low switching. The module is equipped with screw connectors. modRL08_ISO
zł21.01
4 weeks
No product available!
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 2895
zł52.00
24h
Available quantity: 1
Available
Adafruit FeatherWing module with snap relay. It allows you to control high-power components using a microcontroller. It allows switching current to 2A (at 40VAC or 30VDC) and voltage up to 250VAC. Adafruit 2923
zł40.74
24h
Available quantity: 1
Available
Your 5V system can wield great power with this big, beefy relay board. Kit contains all the parts you need to get your high-power load under control. Sparkfun KIT-13815
zł52.71
24h
Available quantity: 1
Available
Module with monostable relay. It allows you to control high-power elements with a microcontroller. Adafruit 3191
zł49.73
24h
Available quantity: 1
Available
Module with MOSFET transistor, 5-36 V, 20 A, switching frequency 1 kHz. DFRobot DFR0457
zł16.86
24h
Available quantity: 6
Available
The module is equipped with eight 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. The board recommended for use with Arduino enables the control of eight relays using only two microcontroller lines. ICSTATION ICSE014A
zł50.41
24h
Available quantity: 2
Available
The module is equipped with four 10A / 250VAC relays controlled independently via a serial bus (UART) or from a PC (through a microUSB connector). The NO / NC contacts of the relays have been led to the ARK screw terminals. ICSTATION ICSE012A
zł44.58
24h
Available quantity: 1
Available
Programmable time module with relay, allows you to set the time and manner of relay reaction on the trigger signal, has a built-in LED display. It can be supplied with voltage from the range of 6 - 30VDC or using the microUSB connector
zł9.67
24h
Available quantity: 40
Available
The module with the HLS8-T73 relay with a load up to 5 A. The board is equipped with a Grove connector and is controlled by a digital input. Seeed Studio 103020005
zł13.80
24h
Available quantity: 7
Available
The module with the TPL5110 timer, which can generate a signal with an adjustable period from 100 ms to 2 h. It also works well as an external Watchdog Timer. Adafruit 3435
zł25.89
4 weeks
No product available!
Module with 2 relays controlled by the I2C interface. Each relay can switch currents up to 25 A at 12 to 280 V AC. SparkFun COM-16810