MAX14840PMB1
ID: 198665
zł159.92
Tax included
zł130.02 tax excl.
Maxim RS-485 Transceiver - Peripheral Module
MAX14840PMB1 Peripheral Module
The IC features symmetrical fail-safe and larger receiver hysteresis, providing improved noise rejection and improved recovered signals in high-speed and longcable applications.
*The maximum communication speed of this module is generally less than 10Mbps due to the presence of current-limiting resistors on the data lines of this module and possibly also the host board.
Refer to the MAX14840E IC data sheet for detailed information regarding operation of the IC.
Description
The MAX14840PMB1 peripheral module provides the necessary hardware to interface the MAX14840E RS-485 transceiver to any system that utilizes PmodTM-compatible expansion ports configurable for a UART interface. The IC is a +3.3V ESD-protected transceiver intended for half-duplex RS-485 communication up to 40Mbps*. These transceivers are optimized for high speeds over extended cable runs, while maximizing tolerance to noise.The IC features symmetrical fail-safe and larger receiver hysteresis, providing improved noise rejection and improved recovered signals in high-speed and longcable applications.
*The maximum communication speed of this module is generally less than 10Mbps due to the presence of current-limiting resistors on the data lines of this module and possibly also the host board.
Refer to the MAX14840E IC data sheet for detailed information regarding operation of the IC.
Features
- Half-Duplex RS-485 Transceivers
- 40Mbps Maximum Data Rate
- Large (170mV) Receiver Hysteresis
- Symmetrical Fail-Safe Receiver Input
- Hot-Swap Capability
- Short-Circuit-Protected Outputs
- Thermal Self-Protection
- Extended ESD Protection for RS-485 I/O Pins
- 6-Pin Pmod-Compatible Connector (Pmod Interface Type 4 UART)
- Example Software Written in C for Portability
- RoHS Compliant
- Proven PCB Layout
- Fully Assembled and Tested
198665
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
40Mbps, +3.3V, RS-485 Half-Duplex
Transceivers, Maxim,SO8, RoHS
zł37.37
24h
Available quantity: 6
Available
Other products in the same category (16)
Pmod I2S2 is a module with 24-bit A / C and D / C audio converters derived from standard 3,5 mm Jack connectors. Thanks to them, it is possible to send and receive stereo audio signals using the I2S protocol. Digilent 410-379
zł187.44
3 weeks
No product available!
Available
High-speed communication module powered by ADM582E. By communicating with the device via UART, users can take advantage of the RS485 communication protocol with speeds up to 16 Mbps. 410-310
zł197.65
3 weeks
No product available!
Available
The Pmod DHB1 uses DRV8833 dual H-Bridge motor driver chip to drive two DC motors or a single stepper motor. 410-259
zł106.04
3 weeks
No product available!
No product available!
No product available!
Evaluation Board with AD7686, 1xADC, 16-bit, Sampling Rate (Per Second) 500k, Analog Devices, RoHS
zł264.77
4 weeks
No product available!
Available
Evaluation Board with AD7685, 1xADC, 16-bit, Sampling Rate (Per Second) 250k, Analog Devices, RoHS
zł162.36
24h
Available quantity: 1
Available
The extension cables let you locate Pmod 6" away from its host board, or use your 12-pin Pmod on a system board with only two 6-pin Pmod headers available. 240-021-2
zł29.69
24h
Available quantity: 4
Available
Available
No product available!
The Pmod SF3 provides users with 32 MB of non-volatile memory through the use of Micron\'s NOR Flash memory (N25Q256A). By using the SPI protocol, users can both write to and read from the flash memory. Digilent 410-340
zł113.68
24h
Available quantity: 1
Available
Evaluation board with AD7687, 1xADC, 16-bit, Sampling Rate (Per Second) 250k, Analog Devices, RoHS
zł184.20
24h
Available quantity: 1
Available
Available
Maxim RS-485 Transceiver - Peripheral Module