- Out-of-Stock
Starter kit with STM32F411RE microcontroller (512 kB Flash, Cortex-M4), with ST-Link/v2 programmer-debugger. It is equipped with Arduino connectors, thanks to which the user can use a wide range of shields available on the market. There are also STMorpho connectors known from the original Nucleo plates on the board. The module is compatible with the mbed.org on-line compiler system and works with most popular programming platforms, including Keil, IAR and environments based on the GCC compiler. Full documentation is available on the product page.

|
1. STM32F411RET6 |
14. Power supply LED |
|
2. SPX3819M5 |
15. User LED |
|
3. AMS1117-5.0 |
16. Fuse 500 mA |
|
4. USB-UART CP2102 |
17. LED TX/RX |
|
5. Arduino connector |
18. 8 MHz |
|
6. ICPS |
19. 32,768 kHz |
|
7. USB-UART |
20. Jumper ADC/I2C |
|
8. USB |
21. Jumper UART |
|
9. SWD |
22. Jumper MCU Current |
|
10. STMorpho |
23. Jumper power supply |
|
11. 6-12V DC |
24. Jumper USB |
|
12. User Button |
25. Jumper przycisku użytkownika |
|
13. Reset |
26. Jumper LED użytkownika |
Compared to the original Nucleo-F411RE plates, Waveshare has introduced numerous amenities to the XNUCLEO-F411RE.
| COMPARE | XNUCLEO | NUCLEO | REMARKS |
|---|---|---|---|
| Arduino compatibility | UNO, Leonardo | UNO | XNUCLEO can be configured by jumper to compatible with UNO (default) or Leonardo |
| Arduino ICSP interface | Yes | None | ICSP is required by certain kinds of shields |
| USB connectivity | Yes | None | The USB connector of NUCLEO is for debugging ONLY, not available for USB connection |
| USB connector | Micro USB | Mini USB | Micro USB is the advanced USB standard |
| Morpho headers mark | Most | None | Now you can check the PCB mark instead of datasheet |
| Common interfaces are connected via | Jumpers | 0Ω resistors | Jumpers are much easier to use, need no soldering |
| UART debugging | Available while in-circuit debugging | Not available while in-circuit debugging | The NUCLEO integrated ST-LINK/V2 functional chip can be simulated as serial port, however, it's not available while in-circuit debugging, whereas XNUCLEO features a stand-alone USB TO UART chip. |
| 8MHz crystal | Yes | None | Timer is more accurate when using external 8MHz crystal |
| 32.768KHz crystal | Yes | None | Required for RTC |
| USB fuse | Yes (500mA) | None | The computer USB interface might be harmed without fuse |
| LEDs | 4 | 1 | The more LEDs, the easier to monitor program running status |
| UART indicator | Yes | None | Data communication is visible now |
| DC input | Yes | None | A convenience |
| Button position | Close to PCB edge | Close to Arduino connector | The button won't be untouchable when connecting with an Arduino shield if it were close to the PCB edge |
| ST-LINK | Separated | Integrated | ST-LINK can be used anywhere else |
| Comes with USB cable | Yes | None |
Manufacturer
Responsible person
STM32 Nucleo development board for STM32 F4 series - with STM32F411RE MCU, 512KB flash memory, STM, RoHS
No product available!
Expansion board with a dynamic NFC/RFID tag based on the M24SR64-Y. The system is equipped with EEPROM memory, the module can be powered by the Arduino connector. STMicroelectronics X-NUCLEO-NFC01A1
Expansion board with L6474 stepper motor driver. It is equipped with a connector compatible with Arduino Uno R3 and STM32 Nucleo. STMicroelectronics X-NUCLEO-IHM01A1
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
The STM32 Nucleo expansion board allows you to control a bipolar stepper motor. The maximum phase current is 2.8A RMS, the controller has overheat protection and overcurrent protection
A universal IR remote designed for NanoPi M1, powered by two AAA batteries. FriendlyELEC RC-100
No product available!
Module with 3 QTRX type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4343
No product available!
Module with 3 QTRX type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 30 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4443
No product available!
Odroid-MC1 Solo is a minicomputer with an Samsung Exynos5422 processor (ARM® Cortex ™ -A15 Quad 2.0GHz / Cortex ™ -A7 Quad 1.4GHz) which has 2 GB of RAM (LPDDR3) available. The module is dedicated to the construction of computer clusters, has a housing that allows you to connect multiple modules with each other.
No product available!
The ISM radio module in the DIP housing. It operates on the 868 MHz frequency. The module complies with FCC, ETSI regulations. HOPE MICROELECTRONICS RFM12B-868DP
No product available!
The ISM radio module in the SMD housing. It operates on the 868 MHz frequency. The module complies with FCC, ETSI regulations. HOPE MICROELECTRONICS RFM12B-868S2P
No product available!
A GFSK transceiver operating in the ISM 2400 ... 2483.5 MHz frequency range. Powered by a voltage of 1.9 ... 3.6 V, the pins are goldpin connectors. It has a built-in PCB antenna. HOPE MICROELECTRONICS RFM73-D
No product available!
A minisumo robot on a tracked chassis with Pololu 75:1 HP motors. Fully assembled robot, additionally requires four AA batteries. Pololu 3126
No product available!
Printed circuit board and programmed SNAKE electronic game system. AVT5639 A +
No product available!
AVT kit for self-assembly of SNAKE electronic game. AVT5639 B
No product available!
The assembled SNAKE electronic game. AVT5639 C
No product available!
A 12-in-1 construction set that teaches the use of solar and hydraulic energy. KSR17
No product available!
Self-assembly kit without TOBBIE robot soldering. KSR18
No product available!
10DOF module with intelligent orientation sensor BNO055 (accelerometer, gyroscope and magnetometer + microcontroller) and BMP280 pressure sensor equipped with Gravity connector. DFRobot SEN0253
No product available!
The ISM radio module in the SMD housing. It works on 433MHz frequency. The module complies with FCC, ETSI regulations. HOPE MICROELECTRONICS RFM12B-433S2P
No product available!
Bluetooth Low Energy module in 5.0 standard. It has a completely integrated Bluetooth software stack and offers a shielded certified version with a built-in antenna. Microchip RN4871-I/RM128
No product available!
Starter kit with STM32F411RE microcontroller (512 kB Flash, Cortex-M4), with ST-Link / v2 programmer-debugger. Modified version compatible with the original Nucleo. Waveshare XNUCLEO-F411RE