- Out-of-Stock
Z23An ABS - Plastic enclosure
ID: 1179801
Plastic enclosure Z23A blue ABS
Description
Colored translucent enclosures - belong to a larger group of two-part enclosures. They are available in colors: red, blue or colorless. The material from which they are manufactured is ABS. It is also possible to purchase enclosures with mounting to the wall (each of which has handles or lug allowing mounting it on a flat surface).
Specification
- Type: Full
- Variant: Without gasket
- Material: ABS
- Color: Blue
- Height: 22.0mm
- Width: 59.0mm
- Length: 84.0mm
- Weight: 33g
Included
- Case Z23An ABS
- Screw 3/20: 1.0 pcs
1179801
Data sheet
- Colour
- Blue
- Materiał
- ABS
- Hermetyczna
- Nie
- Brass bushings
- Nie
- Length
- 84 mm
- Width
- 59 mm
- Height
- 22 mm
Manufacturer Kradex Sp. z o.o. ul. Minerska 4 04-506 Warszawa Poland kradex@kradex.com.pl
Responsible person Kradex Sp. z o.o. ul. Minerska 4 04-506 Warszawa Poland kradex@kradex.com.pl
Other products in the same category (16)
NanoPi M4V2 is a FriendlyELEC single board computer. It uses LPDDR4 RAM memory and adds among others: POWER and RECOVERY micro switches and a microphone input.
Retired
No product available!
NanoPI NEO is a single-board chip from FriendlyELEC with a RAM of 256 MB, successfully competing with the systems created by the giant in this field Raspberry Pi. It is 25% smaller and cheaper than the Raspberry Pi Zero board with similar capabilities
Retired
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
The SparkFun Qwiic Shield for Arduino Nano allows you to add the SparkFun Qwiic ecosystem to development boards that use the Arduino Nano Footprint in an easy-to-assemble shield. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Arduino Nano to four SparkFun Qwiic connectors.
Retired
No product available!
The SparkFun Qwiic Shield for Thing Plus provides an easy-to-assemble way to add the SparkFun Qwiic ecosystem to any development board with the Thing Plus Footprint. It connects the I2C bus (GND, 3.3V, SDA, and SCL) on your Thing Plus to four SparkFun Qwiic connectors. Sparkfun DEV-16138
Retired
No product available!
Cytron 0.8Amp 5V-26V DC Motor Driver Shield - DC motor driver for Arduino
Retired
No product available!
No product available!
No product available!
No product available!
Cytron USB to UART Converter CH340 - USB - UART converter based on the CH340 chip
Retired
No product available!
Logic level converter (4 channels)
Retired
No product available!
The Blebox Wifi controller is dedicated to the most modern digital tapes with 5 V and 12 V, but a LED strip with WS2812 / WS2811 driver is required. BleBox pixelBox
Retired
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, camera, display and Micro SD card connectors. Designed for AI applications in IoT. Seeed Studio 102991150
Retired
No product available!
Evaluation kit with RISC-V Dual Core 64bit chip clocked at 400MHz. Equipped with a USB-UART converter, OV2640 camera, LCD display. The set is enclosed in a housing. Designed for AI applications in IoT. Seeed Studio 110991191
Retired
No product available!
MEMS MSM261S4030H0 microphone module designed to work with Sipeed MAix kits. The module is characterized by high sensitivity, low noise and low cost. Seeed Studio 107990153
Retired
No product available!
Plastic enclosure Z23A blue ABS