- Out-of-Stock
Filament ROSA3D PLA Starter 1.75mm Rubin Red
ID: 1181308
5907753132109
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Rubin Red
Description
1.75 mm PLA filament for 3D printing by ROSA3D. 0.8 kg of filament is wound on the spool. The recommended printing temperature is in the range from 185°C to 225°C, and the bed temperature during printing in the range of 40°C - 60°C, however, when using adhesives, heating the bed is not necessary.
Rosa3D is a Polish manufacturer of filaments intended for both hobby and industrial printing. Thanks to many years of experience and modern machinery, the company is able to provide good quality and accuracy of the diameter and roundness of the filament. Filament PLA Starter from Rosa3D was designed for beginner users of 3D printers. The simplicity of PLA Starter printing will allow you to enjoy aesthetic prints, and over time will convince you to print more and more complex and demanding projects.
PLA is the basic material used in 3D printing. PLA Starter is characterized by low shrinkage and no unpleasant odor. The prints are characterized by excellent layer adhesion and very good detail reproduction. The filament is made of a biodegradable biopolymer. It was made of ingredients approved for contact with food.
Features
- Color: Rubin Red
- Diameter: 1.75 mm
- Diameter tolerance: +/- 0.05mm
- Oval tolerance: +/- 0.02 mm
- Printing temperature: 185°C to 225°C
- Bed temperature: 40°C to 60°C (when using washers or other means to increase the adhesion heating of the table is not required)
- Density 1.24 g/cm3
- Odorless smell
- Elongation at tensile 6%
- Tensile strength (to break) 53 MPa
- Modulus of elasticity at tensile 3500 MPa
- Heat deformation temperature 55°C
- Net weight: 0.8 kg
1181308
Data sheet
- Rodzaj filamentu
- PLA
- Ilość filamentu
- 0,8 kg
- Diameter
- 1,75 mm
- Colour
- Red
You might also like
3D printer with dual color print and heated table. The printer is fully assembled and ready to use. Flashforge Creator PRO
Regular pricezł4,365.91zł3,199.00
24h
Available quantity: 1
Available
Knife designed for trimming and processing of prints from a 3D printer. It consists of a plastic handle and a replaceable, curved blade made of steel
zł9.40
Delivery date unknown
No product available!
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Spray 400ml
zł52.90
24h
Available quantity: 60
Available
Adhesive increasing the adhesion of 3D prints to the glass table. It makes it easier to work with all materials and prevents undesirable curling of the elements. Dimafix Pen 90ml
zł54.46
24h
Available quantity: 262
Available
3D printer with two extruder and a heated table. It is fully assembled and ready to use. Flashforge Creator Pro 2
Regular pricezł5,292.28zł3,999.00
24h
Available quantity: 1
Available
Other products in the same category (16)
No product available!
12 pin GPIO ribbon cable (200mm) for Odroid XU4 and Odroid XU4Q
Retired
No product available!
7 pin GPIO ribbon cable (20 cm) for Odroid C4
Retired
No product available!
No product available!
3-wire cable with JST-ZH plug, 30 cm, 3x1 JST, 1.5 mm pitch
Retired
No product available!
A set for building a four-wheel, remote-controlled vehicle. Equipped with a programmable Arduino Uno R3 controller and set of sensors. modARD_02
Retired
No product available!
No product available!
No product available!
800x480, 7 inch Multicolor Graphic LCD, with capacitive touch screen and stand-alone touch controller
Retired
No product available!
An intelligent socket with the ability to control via Wi-Fi. It allows remote switching on / off of the device powered from 230V mains with a maximum power consumption of 10 A. The device works with the eWeLnik smartphone application
Retired
No product available!
Switch (relay) controlled via GSM / GPRS network. The switch (relay) allows remote control of the device powered from 230 V mains with a maximum power consumption of 16 A. The device works with the eWeLnik smartphone application
Delivery date unknown
No product available!
No product available!
The Google AIY Voice Kit is a set of components designed for the Rasbperry Pi 3 computer, allowing you to build an intelligent voice assistant based on Google Assistant. The kit can also work with TensorFlow. The kit requires self-assembly. Adafruit 3602
Retired
No product available!
This fully-featured UDA1334A I2S Stereo DAC breakout is a perfect match for any I2S-output audio interface. It\'s affordable but sounds great! The NXP UDA1334A is a jack-of-all-I2S-trades: you can use 3.3V - 5V logic levels (a rarity), and can process multiple different formats by setting two pins to high or low. Adafruit 3678
Retired
No product available!
PCB with a programmed layout for an animated 3D LED bomb controlled by an IR remote control. AVT1986 A +
Retired
No product available!
AVT kit for self-assembly of animated 3D LED baubles controlled by IR remote control. AVT1986 B
Retired
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Rubin Red