- Out-of-Stock
New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
Spring for 3D printers 10x25mm (yellow)
ID: 1182162
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table
Description
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table. Prevents the table from bending and cushions it. It ensures a stable position of the table during operation, thanks to which it increases the quality and repeatability of the printed elements.
Features
- Outer diameter: 10 mm
- Inner diameter: 5.5 mm
- Length: 25 mm
- Yellow color
1182162
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Nut with M4 thread for screwing the table to the 3D printer
zł7.66
24h
Available quantity: 17
Available
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table. Set of 4 pcs
zł6.69
24h
Available quantity: 4
Available
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table. Set of 4 pcs
zł5.29
24h
Available quantity: 4
Available
Other products in the same category (16)
Male terminal block, angled, 3-pin. Pitch 3.81mm. Height 7mm. 15EDGRC
Retired
No product available!
MYIR MYC-SAMA5D36 is a single board computer in the form of a card with SO-DIMM 200-pin connector. It has been equipped with the SAMA5D36 processor from Atmel, based on Cortex-A5 cores. It can work with a maximum frequency of 536 MHz. It has 512 MB DDR2 SDRAM, 256 MB NAND FLASH memory. GPIO ports, interfaces have been derived on the SO-DIMM 200-pin connector
Retired
No product available!
No product available!
No product available!
Low cost programmer for STM32 and STM8 microcontrollers fully compatible
with the ST-Link V2
Retired
No product available!
Raspberry PI computer case (transparent), designed for mounting a prototype board
Retired
No product available!
HK ZIPPY Flightmax 5000mAh 2S1P 20C hardcase pack (14079)
Retired
No product available!
Power HD Mini High-Speed Digital Servo 3688HB
Delivery date unknown
No product available!
No product available!
No product available!
No product available!
DevKit8500D DM3730 Evaluation Kit, DevKit8500A AM3715 Evaluation Kit
Retired
No product available!
Bitscope Micro is a miniature measuring instrument with a USB interface, it can act as an 8-channel logic analyzer (40MS / s, 3.3V or 5V) or a 2-channel oscilloscope (bandwidth up to 20MHz). In addition, Bitscope can generate a clock signal as well as sinusoidal, triangular, rectangular and saws
Retired
No product available!
No product available!
Patchcord cable, cat. 5e, with RJ-45 plugs, gray, 2 m long. Equip 225411
Retired
No product available!
Permanent cylindrical neodymium magnet with a diameter of 4 mm and a height of 1,5 mm.
Retired
No product available!
Spring dedicated to the heating table of 3D printers. It allows you to adjust the degree of tightening the knob, and thus enables the proper leveling of the working table