- Out-of-Stock
AVT2895 A +
ID: 189883
INTELLIGENT HOME CENTER - PRINTED PLATES AND PROGRAMMED SYSTEM
INTELLIGENT HOME CENTER - PRINTED PLATES AND PROGRAMMED SYSTEM
Producer: AVT
One of the basic devices in the installation of a smart home is the device-centrifuge - allowing any combination of sensors (eg thermostat) with executive elements (eg a radiator). The mechanical switch system is unacceptable - too large dimensions and low reliability determine this. The solution can be only one - electronic. The presented control unit allows for any combination of 16 sensors with 16 actuators - a total of 256 possible combinations. An additional advantage is the possibility of remote control using an infrared remote control.
The device is particularly recommended in hand-carried intelligent home systems
Selected parameters:
- 16 inputs and 16 outputs
- three work modes
- operating mode signaling - LED and sound signal
- connection to a computer - USB
- software setting of input-output dependencies
- the ability to change the status of each output remotely using an IR remote control
- remote control in the RC5 standard
- power supply - 5Vdc
- tile dimensions:
- 95x56mm
- 47x35mm
- in the set, printed circuit boards, programmed layout and documentation
A version with a set of components for self-assembly is available- Detailed description in EdW 4/09
Download
189883
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Atmel SMART SAM V71 Xplained Ultra development kit with ATSAMV71Q21 microcontroller with ARM Cortex-M7 core. ATSAMV71-XULT
Retired
No product available!
No product available!
No product available!
The module with the 74LVC245AD system allows connecting systems with different supply voltages. Bi-directional operation mode allows you to change the output to the input using a jumper or DIR input, without the need to disconnect the system. MOD-12.Z
Retired
No product available!
MOD-13.Z is a module that allows you to safely and conveniently attach a microSD card to a project with an SPI interface. It has a built-in 74HC125 buffer. MOD-13
Retired
No product available!
The SOIC adapter is used for testing circuits in SMD enclosures. The place for the stabilizer enables the selection of the supply voltage, as well as the supply of additional modules. The module is equipped with a filtering capacitor and space for a polymer fuse. MOD-14.Z
Retired
No product available!
MOD-16.Z replaces the two-button regulation (more - less) with the rotary switch whose state at the given output depends on the direction of rotation. The module has a button in the encoder and a built-in Attiny13 microcontroller.
Retired
No product available!
No product available!
No product available!
The miniature digital potentiometer allows you to replace the analog potentiometer and control the resistance value using two buttons. The module contains inputs of the UP / DOWN buttons (for increasing and decreasing the resistance) and outputs in accordance with the analog potentiometer A, W, B (description on the circuit board). MOD-19.Z
Retired
No product available!
Xmega eXploreGO module with ATXmega128A4U microcontroller (version without MP3). The module is equipped with in DataFlash memory, microSD card connector. MOD-20 / AZ
Retired
No product available!
MOD-21.Z - push button module with bistable operation. The sensor operates based on the AT42QT1012 system.
Retired
No product available!
The Raspberry Pi GPIO connector adapter allows you to output signals from Raspberry Pi to the contact plate. Two LEDs indicate +3.3V and +5V power supply
Retired
No product available!
No product available!
MOD-25.Z - touch sensitive button module with monostable function. The sensor operates based on the AT42QT1011 system.
Retired
No product available!
No product available!
INTELLIGENT HOME CENTER - PRINTED PLATES AND PROGRAMMED SYSTEM