- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
AVT2741 / 2 A
ID: 190531
MAGLEV2 - MAGNETIC LEWITATION - PRINTED PLATE
MAGLEV2 - MAGNETIC LEWITATION - PRINTED PLATE
Producer: AVT
Magnetic levitation relies on the floating of a metal object in the air. This is possible thanks to the magnetic field invisible to the human eye. One of the most important elements of a device that demonstrates this type of phenomenon is a system that allows the levitating body to be maintained in a specific, fixed position. In AVT 2741/2, the infrared beam creates a barrier obscured by the levitating object. Phototransistors were used as sensors. One of them works with the IRED diode, the other examines the level of external lighting. The system uses a limitation of the current flowing through the electromagnet (can be turned off) and an additional button for convenient switching off the coil.
The device is especially recommended for fans of physics and unusual phenomena
Selected parameters:
- IRED diode
- a set of two phototransistors
- ambient lighting compensation circuit
- current limiter flowing through the electromagnet
- power supply - 12 V
- printed circuit board and documentation included
A version with a set of components for self-assembly is available- Detailed description in
Download
190531
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
Plastic holder that could fit all the boards with Arduino UNO size (68,6 mm x 53,4 mm). Contains 5 pieces in different colours. A000018
Delivery date unknown
No product available!
CryptoShield is a dedicated security peripheral for the Arduino. This shield adds specialized ICs that perform various cryptographic operations which will allow you to add a hardware security layer to your Arduino project. It also is a nice device for those performing embedded security research. DEV-13183
Retired
No product available!
No product available!
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
It is a standard audio-video cable, which can be successfully used to connect Banana Pi M1 or Raspberry Pi 1 model B and A. Cable length is 98 cm, has two ends of the chinch type.
Retired
No product available!
COM-11964 Button a white economy grade 100mm diameter (outside diameter) dome illuminated push button comes with an LED, securing nut and a long life horizontal microswitch.
Retired
No product available!
Cobbler Plus - adapter enabling connection of GPIO Raspberry Pi A +, B + and Pi 2 lines to the contact plate (2.54 mm). The version is assembled. Adafruit 2029
Retired
No product available!
MAGLEV2 - MAGNETIC LEWITATION - PRINTED PLATE