- Out-of-Stock
New products
New products New products
zł119.00
Delivery date unknown
zł119.00
Delivery date unknown
AVT755 B
ID: 192642
POWER UNIT - A KIT FOR SELF-ASSEMBLY
POWER UNIT - A KIT FOR SELF-ASSEMBLY
Producer: AVT
A simple system that allows you to convert a stereo amplifier into a device with four times higher peak power (doubled continuous power). This is the so-called inverter - its both outputs provide signals of equal amplitudes, but opposite in phase. After connecting the finished power amplifiers, also on their outputs there will be an opposite signal in phase, with a large amplitude. In this way, the bridge amplifier type BTL (Bridge Tied Load) will be created. This allows a significant increase in the output power.
ATTENTION!!! The doubler should not be used for car amplifiers that are originally designed like bridge systems.
The device is especially recommended for converting several years old stereo amplifiers or radios equipped with them
Selected parameters:
- two outputs delivering a signal with the same amplitude but the opposite phase
- 1V / V gain (in both tracks)
- maximum output output value 2Vpp (0.7Vsk) for 6V power supply
- one power supply
- possibility of mounting potentiometers for precise reinforcement of both channels
- power supply - 6-15 Vdc
- a printed circuit board (integrated circuit version), a set of elements and documentation
- Detailed description in EdW 3/07
Download
192642
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
No product available!
Michel Chipot
Delivery date unknown
No product available!
Flash programmer for STM8 series of flash microcontrollers with on-chip flash, Segger
Retired
No product available!
No product available!
Freescale starter kit with Kinetis KE04Z microcontroller (Cortex-M0 +, 5V power supply ), integrated with the OpenSDA debugger-programmer, capacitive switch, LED-RGB and MEMS 3D accelerometer. Arduino-compatible outputs.
Retired
No product available!
AVT kit for self-assembly of the ON / OFF timer. AVT1821 B
Retired
No product available!
No product available!
PCB and programmed arrangement for a microprocessor fear for birds. AVT3135 A +
Retired
No product available!
The stabilizer module is used to stabilize the output voltage at an appropriate level and filter interference. The module can be supplied with voltage up to + 16V, and the output voltage is + 5V. MOD-06 / 5V.Z
Retired
No product available!
ESP32-P4-WIFI6-DEV-KIT-C is the most comprehensive kit with a 10.1" display, camera and full audio-video support, dedicated to HMI applications, intelligent control systems and interactive IoT devices. It provides high performance, multi-protocol connectivity and integration capabilities with AI platforms and industrial-grade security systems.
Retired
No product available!
HAT for powering over Ethernet (PoE) for Raspberry Pi. It allows you to use the PoE interface to power the minicomputer via an Ethernet cable
Retired
No product available!
Wires with Pre-crimped Terminals 50-Piece Rainbow Assortment F-F 6"
Retired
No product available!
250-Piece Short Jumper Wire Kit without Case (wires up to 1-inch long)
Retired
No product available!
No product available!
433M wireless module for SPI interface, vertical pinheaders, 1.27mm pitch
Retired
No product available!
MYIR MYC-JA5D44 is a single-board computer in the form of a card with SO-DIMM 200-pin connector. The SAMA5D44 processor from Atmel, based on Cortex-A5 cores, has been equipped. It can work with a maximum frequency of 600 MHz. It has 512 MB of DDR2 SDRAM, 512 MB of NAND Flash memory. GPIO ports, interfaces have been derived on the SO-DIMM 200-pin connector.
Retired
No product available!
POWER UNIT - A KIT FOR SELF-ASSEMBLY