- Out-of-Stock
AVT1584 B
ID: 192974
LED BULB - A KIT FOR INDEPENDENT INSTALLATION
LED BULB - A KIT FOR INDEPENDENT INSTALLATION
Producer: AVT
The presented system enables powering of LED diodes or their set with a current of maximum 1A. Powered from 12V, it was designed to replace the 20W halogen lamp (eg: in table lamps). Four bright LEDs emit sufficient light to read the book at ten times less (halogen) power.
It is possible to use diodes of different colors - then the system can serve as a glowing module-decorative element.
The device is especially recommended in home lighting systems
Selected parameters:
- supervising the value of the current feeding the LED diodes
- high efficiency of the system (70-95%)
- possibility to replace 12V halogen lamps
- DC or AC power supply
- power supply - 9-12Vac (9-16Vdc)
- in the set a printed circuit board, a set of elements and documentation
- A detailed description in EP 8/10
Download
192974
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Anti-static brush, brush for cleaning printed circuit boards, elements after the soldering process
Retired
No product available!
Antimagnetic tweezers, sharp, made of stainless steel, resistant to most solvents and cleaning agents. 00-sa
Retired
No product available!
ZD-409 resistance soldering machine with a power of 48W is a tool useful when disassembling SMD and DIL components on printed circuits.
Retired
No product available!
Multi-channel circuit testing multimeter that uses your smartphone or tablet, through Bluetooth 4.0, as a wireless, high-resolution graphical display. Each Mooshimeter is able to safely measure 600V at 10A with 24bit resolution from up to 150 feet away. TOL-13843
Retired
No product available!
Analog Test Shield for Arduino Development, AD/DA. Integrates DAC circuit and amplifier circuit.
Retired
No product available!
USB TO UART solution with USB micro connector. Waveshare 11315
Retired
No product available!
Waveshare WIFI501 is a mother board designed to be used with WiFi modules like WIFI232 series, WIFI-LPT100. It provides an easy way to test/evaluate these WiFi to UART modules
Retired
No product available!
No product available!
No product available!
Banana Pi M2+ is another ARM SoC powered development board that offers great computing performance in an ultra portable form factor. It is a 65mm square with Allwinner H3 Quad-core A7 SoC and 1GB DDR3 RAM
Retired
No product available!
Self-assembly DIY enclosure for Banana Pi M2+, transparent
Retired
No product available!
Lithium Polymer rechargeable cell with a Protection circuit. Compatible with ODROID-C0
Retired
No product available!
MYIR MYC-JA5D44 is a single-board computer in the form of a card with SO-DIMM 200-pin connector. The SAMA5D44 processor from Atmel, based on Cortex-A5 cores, has been equipped. It can work with a maximum frequency of 600 MHz. It has 512 MB of DDR2 SDRAM, 512 MB of NAND Flash memory. GPIO ports, interfaces have been derived on the SO-DIMM 200-pin connector.
Retired
No product available!
MYIR MYC-C7Z020 is a single board computer module based on the MYC-C7Z020 chip. This system consists of a dual-core processor based on the Cortex-A9 core (667 MHz) and the Artix-7 FPGA chip. The board has 1 GB of DDR3 SDRAM, 4 GB of eMMC memory and 32 MB of QSPI Flash memory. The board is equipped with numerous peripherals, the outputs of which have been led out on two 140-pin connectors.
Retired
No product available!
UART GPS Module, NEO-7M-C onboard, straight/vertical pinheader
Retired
No product available!
The Arduino UNO WiFi board is based on the ATmega328 and it has an integrated ESP8266 WiFi Module. If you are starting out with Arduino, or starting with IoT, this is the board to get. A000133
Retired
No product available!
LED BULB - A KIT FOR INDEPENDENT INSTALLATION