- Out-of-Stock
AVT2743 / 1 B
ID: 192988
DISCO SUPEREFECT - A SELF-ASSEMBLY KIT
DISCO SUPEREFECT - A SELF-ASSEMBLY KIT
Producer: AVT
An extremely effective disco device. Despite the use of the three cheapest and very popular integrated circuits, a very large number of lighting effects were obtained - thanks to that, the use of a microprocessor became unnecessary. The system enables the generation of color flashes in both music and rhythm of the built-in variable frequency generator.
The device consists of two main blocks. The analogue is used to amplify, filter and form into the impulses sounds coming from the environment and received by the microphone. The digital part responds to these impulses, it turns on the light fields in the appropriate sequence. The system is completely separated from the mains.
The device is especially recommended for discos, colorful music lovers and light effects enthusiasts
Selected parameters of the controller:
- sound control or a built-in generator
- built-in microphone
- regulation of the acoustic signal level
- ten half-light ones
- light sources - LED diodes, the possibility of using car bulbs
- pulse length adjustment from the generator
- various light effects, e.g. stroboscopic effect, wave
- effects coding - jumpers
- power supply - 12 V
- in the set of printed circuit boards (main + 1p.m. LED matrixes), a set of elements with red super-bright LED diodes and documentation
Attention. Additional LED matrix plates are available under the / 2 mark
- Detailed description in
Download
192988
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Display with a touch screen (resistive panel) with a diagonal of 3.5 inches and a resolution of 480 x 320 pixels. Uses the SPI interface. Intended for use with the Raspberry Pi Zero / B + / 2/3 minicomputer. ArduCAM U470301
Retired
No product available!
A set of basic electronic components complete with contact plate, connecting cables and Mega2560 R3. It is ideal for beginner electronics who also know Arduino. ArduCAM KB0003
Retired
No product available!
A set of basic electronic components complete with contact plate, connecting cables and board compatible with Arduino UNO R3. It is ideal for beginner electronics who also know Arduino. Uctronics KB0002
Retired
No product available!
A set of basic electronic components complete with contact plate, connecting cables and Arduino UNO R3. It is ideal for beginner electronics who also know Arduino. ArduCAM KB0001
Retired
No product available!
Orange filament 1.75 mm 0.85 kg Easy PLA by Fiberlogy
Retired
No product available!
No product available!
No product available!
12 pin GPIO ribbon cable (200mm) for Odroid XU4 and Odroid XU4Q
Retired
No product available!
7 pin GPIO ribbon cable (20 cm) for Odroid C4
Retired
No product available!
No product available!
3-wire cable with JST-ZH plug, 30 cm, 3x1 JST, 1.5 mm pitch
Retired
No product available!
A set for building a four-wheel, remote-controlled vehicle. Equipped with a programmable Arduino Uno R3 controller and set of sensors. modARD_02
Retired
No product available!
No product available!
No product available!
800x480, 7 inch Multicolor Graphic LCD, with capacitive touch screen and stand-alone touch controller
Retired
No product available!
An intelligent socket with the ability to control via Wi-Fi. It allows remote switching on / off of the device powered from 230V mains with a maximum power consumption of 10 A. The device works with the eWeLnik smartphone application
Retired
No product available!
DISCO SUPEREFECT - A SELF-ASSEMBLY KIT