- Out-of-Stock
AVT1518 B
ID: 193214
ELECTRONIC SUBSIDIARY ISOSTAT - SELF-ASSEMBLY KIT
ELECTRONIC SUBSIDIARY ISOSTAT - SELF-ASSEMBLY KIT
Producer: AVT
I think every electronics knows what an Isostat element is. Old, but solid sequential switches, just over a dozen years ago, completely dominated the mass electronics market. These switches could be combined in different configurations, as dependent or independent, on metal slats.
Currently, we present a system that can replace the previously presented 'relics' of electronics. It was designed so that it would be possible to insert the tiles directly in place of the old contact switches. Of course, the system can be used in many other ways.
The device is especially recommended for the renovation of old equipment equipped with Isostats
Selected parameters:
- modular construction that allows you to replace the required number of switches
- executive elements - relays
- the size of the plate and the spacing of leads allowing for direct soldering in the fields after Isostats
- mutually dependent switches
- construction using SMD elements
- power supply - 5Vdc
- in the set a printed circuit board, a set of elements (to one module) and documentation
Note: The offered kit consists of only one module. The picture shows 5 connected modules.
A detailed description in EP 4/09
193214
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
The Leonardo ETH is a microcontroller board based on the ATmega32U4 and the new W5500 TCP/IP Embedded Ethernet Controller (datasheet).
Retired
No product available!
The Arduino 9 Axes Motion Shield allows your Arduino to measure movement: orientation, acceleration and magnetic field. A000070
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Retired
No product available!
Plastic holder that could fit all the boards with Arduino UNO size (68,6 mm x 53,4 mm). Contains 5 pieces in different colours. A000018
Delivery date unknown
No product available!
CryptoShield is a dedicated security peripheral for the Arduino. This shield adds specialized ICs that perform various cryptographic operations which will allow you to add a hardware security layer to your Arduino project. It also is a nice device for those performing embedded security research. DEV-13183
Retired
No product available!
No product available!
Banana Pi R1 acrylic clear case. The case needs to be assembled by yourself
Retired
No product available!
The housing for the Banner PI G1 Debugger made of transparent plastic. Housing for self-assembly
Retired
No product available!
The I2C electric level conversion module is specifically designed for Banana Pi. The module converts the 3.3V of I2C electric level to 5V level or converts 5V to 3.3V
Retired
No product available!
BPI AD/DA extend module with the PCF8591 single-chip, single-supply low-power 8-bit CMOS data acquisition device with four analog inputs, one analog output and a serial I2C-bus interface
Retired
No product available!
No product available!
5dB antenna for the Banana Pi R1 router in the version with 300Mps wifi and five LAN 100/1000 ports.
Retired
No product available!
STM32F103 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC3200 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
CC2530 and CC2540 programming cable for Open Debugger Burn Board and Banana Pi G1 connection
Retired
No product available!
ELECTRONIC SUBSIDIARY ISOSTAT - SELF-ASSEMBLY KIT