- Out-of-Stock
New products
New products New products
Available
zł73.14
24h
Available
zł1,049.01
24h
Available
AVT924 C
ID: 193357
PROGRAMMED LIGHT CONTROLLER - SET ASSEMBLED AND STARTED
PROGRAMMED LIGHT CONTROLLER - SET ASSEMBLED AND STARTED
Producer: AVT
The light controller uses a microcontroller. The system has eight outputs for direct control of LEDs that illuminate. These outputs can also be used to control relays - in this way, high-power bulbs can be connected to the module, powered from 230 V mains. Light sequences are not imposed, each user programs them individually. The maximum length of one "light program" consists of 254 steps - individual configurations. Such a program is saved in the non-volatile EEPROM memory. The speed of change is regulated by two buttons.
The device is especially recommended for lovers of light effects, animators of exhibitions, performances and concerts
Selected parameters:
- eight buffered outputs for controlling light sources
- number of program steps - 254
- different types of output circuits, e.g. LEDs or relays
- operation status indication - LED
- UP / DOWN buttons to adjust the speed of change playback
- power supply - 9-15 Vdc
- system assembled and running
Detailed description in EP 4/06
Documentation
193357
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
No product available!
ROSA3D filament made of high-quality PET-G granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PET-G Standard Red Wine Transparent
Retired
No product available!
KT30 multimeter from Kemot with 3 1/2 digits display. The multimeter enables measurement of: DC and AC voltage up to 500 V, current up to 10 A, resistance up to 20 MΩ. Diode, transistor and circuit continuity tester
Retired
No product available!
The GY-GPS6MV1 module is a board containing the U-blox NEO-6M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART signal outputs
Retired
No product available!
No product available!
No product available!
Spray CLEANSER PCC 15 with a capacity of 150ml, with a brush is a reliable solution for cleaning printed circuit boards and soldering residues. MICROCHIP
Retired
No product available!
Starter kit with micro:bit v2. Includes USB cable, battery basket and PVC casing. OKdo micro:bit Getting Started Kit
Retired
No product available!
The eXtremestyle silicone cable (1.5m length) with US Type C connector. Allows you to charge the device and transfer data. eXtreme S15UCW
Retired
No product available!
USB TO UART solution with USB Type A connector, Waveshare
Retired
No product available!
The 4-channel DC motor driver module is designed to work with the M5Stack sets. Powered with the voltage from 6 to 12 V, it can support encoders. M5Stack DC MOTOR
Retired
No product available!
No product available!
No product available!
Pre-installed Ubuntu 16.04 or latest version. eMMC Version 5.0 interface or higher version from Samsung. JEDEC/MMCA version 5.0 : HS400 interface with 8bit DDR mode. The eMMC chipset is only compatible with Amlogic S905 and S805 series(ODROID-C1+ / C0 / C2)
Retired
No product available!
No product available!
ARM Cortex-M3 MCU, 512 kB Flash, 64 kB SRAM, Ethernet, USB Device/Host, 2xCAN, I2S, DAC, LQFP100, RoHS
Retired
No product available!
PROGRAMMED LIGHT CONTROLLER - SET ASSEMBLED AND STARTED