- Out-of-Stock
AVT1446 A +
ID: 193460
THERMOMETER - PRINTED PLATES AND PROGRAMMED SYSTEM
THERMOMETER - PRINTED PLATES AND PROGRAMMED SYSTEM
Producer: AVT
A thermometer with battery power that uses a graphic display from a mobile phone to display the temperature. This means low energy consumption and enables convenient 3-volt power supply. The reading is presented in both digital and analogue form. The display is possible in normal and inversion mode (negative). The whole device has small dimensions and is easy to make and run.
The device is especially recommended wherever temperature measurement is required; due to the simplicity of implementation, even a novice electronics can put them together
Selected parameters:
- reading - 84 x 48 pixels LCD graphic display
- digital and analog temperature reading
- the possibility of normal and inversion display
- sensor measuring range -55 - + 125 stC
- digital reading range -55 - +125 stC
- analog reading range 0 - +32 stC
- measuring resolution 0.1 stC
- power supply -3 V (battery)
- a printed circuit board, programmed layout and documentation in the set
A version with a set of components for self-assembly is available
Detailed description in EP 3/07
Download
193460
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
Camera board for the STM32F407G-DISC1 set. It allows you to capture an image with a resolution of 1280 x 1024 pixels (1.3MP). The set includes a flexible cable that allows the camera to be connected to the STM32F4DIS-BB expansion board
Retired
No product available!
The MyoWare Muscle Sensor is now designed to be wearable allowing you to attach biomedical sensor pads directly to the board itself. DEV-13687
Retired
No product available!
No product available!
This in-system programmer can be used to program AVR microcontrollers and AVR-based controller boards, such as our Orangutan robot controllers and the 3pi robot. Pololu 3170
Retired
No product available!
EXtreme CC312U 3100mA power supply / car charger with two USB ports, allows you to charge phones, navigation, mp3 / mp4 players and connect Raspberry Pi computers
Retired
No product available!
AVT kit for self-assembly of an extremely effective bomb clock. AVT3128 B
Retired
No product available!
AVT kit for self-assembly of the battery capacity meter and the level of battery consumption. AVT5500 B
Retired
No product available!
433M wireless module for SPI interface, vertical pinheaders, 1.27mm pitch
Retired
No product available!
high performance e-compass, 3D accelerometer and 3D magnetometer module, I2C interface, LSM303DLHC on board
Retired
No product available!
three-axis digital output gyroscope, three-axis angular rate sensor module, I2C/SPI interface, L3G4200D on board
Retired
No product available!
High-power brushed DC motor with a 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is perpendicular to the motor shaft, and a built-in safety clutch. Pololu 1511
Retired
No product available!
High-power brushed DC motor, 120:1 reduction gearbox, intended for operation at 4.5 V, 9.7mm-long gearbox, 3 mm-diameter D-shaped output shaft that is offset from but parallel to the motor shaft, built-in safety clutch. Pololu 1512
Retired
No product available!
This compact, inexpensive plastic gearmotor (brushed DC motor with a 120:1 reduction gearbox) is well suited for use in small robots. While intended for operation at 4.5 V, it should run comfortably in the 3 V to 6 V range.
Retired
No product available!
Raspberry computer case: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B + in gray with metal
Retired
No product available!
Battery: Li-Ion; 3.7V; 1000mAh; Outputs: wires with 2-pin JST-PH connector; 50.8 mm x 33.5 x 5.9 mm. PRT-13813
Retired
No product available!
No product available!
THERMOMETER - PRINTED PLATES AND PROGRAMMED SYSTEM