- Out-of-Stock
zł10,639.61
.png)
New products
New products New products
AVT2736 A
ID: 193708
400 W AMPLIFIER - PRINTED PLATE
400 W AMPLIFIER - PRINTED PLATE
Producer: AVT
This amplifier was designed at the request of EdW readers. High output power, with a relatively low supply voltage, is possible due to the use of two power terminals connected in a bridge circuit (BTL). The presence of an input differential amplifier minimized the problems associated with running the system's mass.
Two heat sinks with fans were used as cooling - ready modules for cooling processors in a PC. Thanks to this, the entire system is characterized by relatively small dimensions. The amplifier can be used as a guitar stove.
The device is especially recommended for audiophiles and musicians-electronics
Selected parameters of the amplifier:
- peak power - up to 400 W (optionally 2x 100 W)
- delayed speaker connection system, mute after disconnecting the power supply
- active cooling (fans)
- load - 8 ohms
- power supply - 2x45 V
- printed circuit board and documentation included
A version with a set of components for self-assembly is available- Detailed description in
Download
193708
Manufacturer
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Responsible person
- AVT SPV Sp. z o.o.
- Leszczynowa 11
- 03-197 Warszawa
- Poland
- [email protected]
Other products in the same category (16)
Printed circuit board and programmed circuit for a remotely controlled 4-channel switch. AVT5599 A +
Retired
No product available!
AVT kit for self-assembly of a remotely controlled 4-channel switch. AVT5599 B
Retired
No product available!
Assembled, remote controlled 4-channel switch. AVT5599 C
Retired
No product available!
DIN rail housing for Raspberry computers: Pi 3 model B +, Pi 3 model B, Pi 2 model B and Pi 1 model B +. Italtronic 10.0052450.RMB
Retired
No product available!
An evaluation kit VisionSTK-NAND contains: VisionSOM-6ULL board (variant with eMMC 4 GB memory and WiFi/BT module) and VISIONCB-STD evaluation board.
Retired
No product available!
An evaluation kit VisionSTK-NAND contains: VisionSOM-6ULL board (variant with NAND 512 MB memory and WiFi/BT module) and VISIONCB-STD evaluation board.
Retired
No product available!
The STM32 Nucleo-144 boards provide an affordable and flexible way for users to try out new concepts and build prototypes by choosing from the various combinations of performance and power consumption features, provided by the STM32 microcontroller.
Retired
No product available!
No product available!
No product available!
Infrared thermometer module. It is characterized by high sensitivity and accuracy, low noise and low energy consumption. DFRobot SEN0093
Retired
No product available!
Connector for connecting the 50-pin tape with 0.5 mm pitch to the printed circuit board. PCA-6-LA-50-HL-3
Retired
No product available!
The Bluetooth module complies with the Bluetooth SPP specification and the Bluetooth 2.1 + EDR standard. Powered by 3.3/5V.
Retired
No product available!
UART GPS Module, NEO-7M-C is a module containing the U-blox NEO-7M GPS receiver system. The tile also includes RTC backup battery, antenna connector (U.FL), voltage stabilizer and UART interface signal outputs. Waveshare UART GPS NEO-7M-C
Retired
No product available!
The LoPy board is an IoT module with a 32-bit microcontroller, equipped with LoRa, Wifi and Bluetooth (BLE) communication. Seeed studio 109110001
Retired
No product available!
Dragino LoRa Shield is an expansion board for Arduino (Uno, Leonardo, Mega, DUE) with a LoRa communication module (RFM98W system). Works at 433 MHz, maximum power up to 100 mW. In the set with the plate there is also an antenna. Seeed studio 113990194
Retired
No product available!
Module with color sensor TCS34725FN. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 101020341
Retired
No product available!
400 W AMPLIFIER - PRINTED PLATE