- Out-of-Stock
AVT1468 A
ID: 193793
LOCAL RADIOPHEADING - PRINTED PLATES
It is a simple remote control, one channel. Information is sent via radio, the state at the transmitter's input is transferred to the receiver's output. The device gives the possibility of setting the address or unique code, thanks to which the devices are resistant to accidental activation. In addition, many such sets can work in one area and everyone will react only to their own pair.
The device can be used in alarm systems to notify about the occurrence of an alarm or about the state of detectors, for remote control, and also wherever it is necessary to transmit wirelessly the recall information.
The device is especially recommended where it is necessary to wirelessly transmit signals
Selected parameters:
- transmission medium: radio waves, frequency 433MHz, permanent code
- addressing: 8-section switch - 255 combinations
- input: reacting to a short circuit (eg a button) or a break (eg a reed sensor)
- output: voltage max. 16V, 2A and relay max. 250VAC 2A
- power supply 7 ... 16V transmitter, power consumption at rest <1mA, recommended: 6F22 battery (9V)
- receiver supply 7 ... 16, power consumption without connected load max. 50mA, recommended: power supply 12V
- PCB dimensions: transmitter 29x70 mm, receiver: 34x70 mm
- project AVT 1468 EP 07/08
Download
193793
Manufacturer AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Responsible person AVT SPV Sp. z o.o. Leszczynowa 11 03-197 Warszawa Poland zamowienia@avt.pl
Other products in the same category (16)
PCB with a programmed layout for an animated 3D LED bomb controlled by an IR remote control. AVT1986 A +
Retired
No product available!
AVT kit for self-assembly of animated 3D LED baubles controlled by IR remote control. AVT1986 B
Retired
No product available!
A printed circuit board and a programmed layout for an animated 3D LED Christmas tree. VT1988 A +
Retired
No product available!
Zetaw AVT for self-assembly of the animated Christmas tree LED 3D. AVT1988 B
Retired
No product available!
No product available!
A circuit board and a programmed layout for a falling meteorite. AVT3186 A +
Retired
No product available!
AVT kit for self-assembly of a falling meteorite. AVT3186 B
Retired
No product available!
Assembled falling meteorite. AVT3186 C
Retired
No product available!
Printed circuit board and programmed thermostat system with LED display. AVT3220 A +
Retired
No product available!
AVT kit for self-assembly of a thermostat with LED display. AVT3220 B
Retired
No product available!
Assembled thermostat with LED display. AVT3220 C
Retired
No product available!
A circuit board for the (half) home automation system - a four-channel ON / OFF module. AVT3212 A
Retired
No product available!
AVT kit for self-assembly of the (half) home automation system - four-channel ON / OFF module. AVT3212 B
Retired
No product available!
Assembled system (half) of home automation - four-channel ON / OFF module. AVT3212 C
Retired
No product available!
The PCF8574 IO expansion board is an 8-bit I / O expander controlled by the I2C interface. Up to 8 PCF8574 IO expansion cards can be connected to the I2C bus, providing up to 64 I / O ports. Waveshare 3708
Retired
No product available!
MYIR MYS-7Z0007S-C - KIT is a set of elements with a single board computer based on the Xilinx XC7Z007S-1CLG400C (Zynq-7007S) system. This system consists of a single-core processor based on Cortex-A9 core, which can operate at a maximum frequency of 667 MHz and Artix-7 FPGA. The computer is equipped with 512 MB of DDR3 SDRAM, 4 GB of eMMC memory and 16 MB of QSPI Flash memory
Retired
No product available!
LOCAL RADIOPHEADING - PRINTED PLATES