- Out-of-Stock
These premium wires are stranded 26AWG wires with female terminals on one end and male terminals on the other end. Together with our 0.1" crimp connector housings, these wires can be used to make custom cables with 0.1" (2.54mm) connectors. The assortment of 24" (60 cm) wires includes five each of ten different colors.
![]() |
| 0.1" connector custom cable. |
|---|
These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connector housings on the ends. By combining these wires with our crimp connector housings, you can quickly and easily create custom cables with 0.1" (2.54mm) connectors that mate with various 0.1"-spaced connectors, including male and female headers and solderless breadboards. Just pick the housing for the correct number of pins, pick the colors and genders for your wires, and snap them into the housings (note: it’s not easy to get the wires back out, so plan carefully!). No soldering is required!
You can easily make cable harnesses or assemblies that branch from one connector on one side to multiple connectors on the other (an example of this is shown in the picture to the right); you can also cut off one pre-crimped end and solder the wires directly to components to make swapping connections easy, as shown in the motor picture below.
The wires are available in six lengths—3" (7.5 cm), 6" (15 cm), 12" (30 cm), 24" (60 cm), 36" (90 cm), and 60" (150 cm)—and in ten colors:
![]() |
| 0.1" connector custom motor cable. |
|---|
These are the same colors as those used on resistor color codes and rainbow ribbon cable. The wire packs of different lengths include different quantities of wires. The table below shows the quantity included for a particular length-color combination:
| length | monochromatic pack quantity | rainbow pack quantity |
|---|---|---|
| 3" | – | 50 (5 of each color) |
| 6" | 10 | 50 (5 of each color) |
| 12" | 10 | 50 (5 of each color) |
| 24" | 5 | 50 (5 of each color) |
| 36" | 5 | 20 (2 of each color) |
| 60" | 2 | 10 (1 of each color) |
These wires can be purchased with male terminals on both ends, female terminals on both ends, or one male and one female terminals. These crimped terminals are designed for use with 0.1" (2.54 mm) male headers and female headers, solderless breadboards, and prototyping PCBs. Note that we also sell the crimp pins by themselves if you want to crimp your own wires.
![]() |
![]() |
| Female crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
| Male crimp pin for 0.1" housings crimped onto a wire. |
|---|
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x3-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x2-Pin 25-Pack |
![]() |
0.1" (2.54mm) Crimp Connector Housing: 1x1-Pin 25-Pack |
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The soldering set includes a 48W ZD-99 soldering station, tin, rosin, tweezers, arrowhead and tape
No product available!
Orange Pi Zero Plus H5 Quad Core Cortex-A53 Open Source 512MB DDR3 Development Board Mini PC
No product available!
A plate with a dynamic NFC / RFID tag based on the ST25DV04K chip. The module can be powered by the Arduino connector and by energy recovery from the radio track. The board includes an Arduino Uno R3 compatible connector and can be combined with STM32 Nucleo series. The plate also has an antenna with a diameter of 54 mm. X-NUCLEO-NFC04A1
No product available!
Printed circuit board for multi-input switch. AVT1966 A
No product available!
AVT kit for self-assembly of multi-input switch. AVT1966 B
No product available!
No product available!
PCB for protecting the 6V gel battery. AVT1970 A
No product available!
AVT kit for self-assembly of 6V gel battery protection. AVT1970 B
No product available!
Assembled 6V gel battery protection. AVT1970 C
No product available!
Printed circuit board with programmed night lamp controller system with time system. AVT1969 A +
No product available!
AVT kit for self-assembly of the bedside lamp controller with time system. AVT1969 B
No product available!
Assembled night lamp controller with time system. AVT1969 C
No product available!
PCB for amplifier for pulse generator. AVT1961 A
No product available!
External AVT for self-assembly of amplifier for pulse generator. AVT1961 B
No product available!
Assembled amplifier for the pulse generator. AVT1961 C
No product available!
PCB with programmed layout for the RGB color mixer. AVT5596 A +
No product available!